10-INCH PORTABLE CONTRACTOR TABLE SAW 36-6022

10-INCH PORTABLE CONTRACTOR

TABLE SAW

SCIE SUR TABLE PORTABLE CONTRACTOR DE 10 PO

SIERRA DE MESA DE CONTRATISTA PORTÁTIL DE 10

PULGADAS

www.DeltaMachinery.com

36-6022

Instruction Manual

To reduce the risk of serious injury, thoroughly read and comply with all warnings and instructions in this manual and on product.

KEEP THIS MANUAL NEAR YOUR PRODUCT FOR EASY REFERENCE AND TO INSTRUCT OTHERS

Français (36)

Español (70)

2 3

TABLE OF CONTENTS

FUNCTIONAL DESCRIPTION .................................................. 2

IMPORTANT SAFETY INSTRUCTIONS ................................... 3

SAFETY-SYMBOLS-DEFINITIONS .......................................... 3

GENERAL SAFETY RULES ...................................................... 3

PROPOSITION 65 WARNING ................................................... 4

TABLE SAW SAFETY RULES ................................................... 5

TERMINOLOGY ................................................................... 5

GENERAL POWER TOOL SAFETY..................................... 5

SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND .......

RIVING KNIFE ASSEMBLY.................................................. 6

MAKING A PUSH STICK ..................................................... 6

KICKBACKS ........................................................................ 7

POWER CONNECTIONS .......................................................... 8

POWER SOURCE ............................................................... 8

EXTENSION CORDS ........................................................... 8

UNPACKING .............................................................................. 9

PACKAGE CONTENTS ....................................................... 9

CONTENTS OF HARDWARE BAGS ................................. 10

ASSMEBLY ............................................................................... 10

ASSEMBLING UPPER STAND .......................................... 11

ASSEMBLING THE STAND ............................................... 12

WHEELS ............................................................................ 13

PEDAL ASSEMBLY ........................................................... 14

UPPER STAND ASSEMBLY .............................................. 16

ATTACH SAW TO STAND ASSEMBLY .............................. 18

HEIGHT ADJUSTMENT KNOB INSTALLATION ............... 19

BLADE AND GUARDS ...................................................... 19

ATTACH THE BLADE ........................................................ 19

INSERT THROAT PLATE ................................................... 21

ANTI-KICKBACKS PAWLS AND BLADE GUARD ............ 23

OUTFEED SUPPORT STOPS ........................................... 24

ONBOARD STORAGE ....................................................... 26

OPERATION ............................................................................. 27

TURNING THE SAW ON/OFF ........................................... 28

TRANSPORTING THE SAW .............................................. 28

MAKING CUTS ........................................................................ 29

RIP CUTS .......................................................................... 30

BEVEL RIPPING ................................................................ 30

CROSSCUTTING .............................................................. 31

BEVEL CROSSCUTTING .................................................. 31

MITER CUTS ..................................................................... 31

COMPOUND MITER CUTS............................................... 32

LARGE PANEL CUTS ........................................................ 32

NON-THROUGH CUTS ..................................................... 32

MAKING A NON-THROUGH CUT .................................... 32

MAKING A DADO CUT ..................................................... 33

CUTTING AIDS AND ACCESSORIES .................................... 33

PUSH STICK ..................................................................... 33

AUXILIARY MITER GAUGE FACING ................................. 34

PUSH BLOCK .................................................................... 34

FEATHERBOARD .............................................................. 35

CUT OFF GAUGE .............................................................. 35

JIGS ................................................................................... 35

MAKING ADJUSTMENTS ....................................................... 36

LEVELING THE THROAT PLATE ....................................... 36

SQUARING THE BLADE VERTICALLY TO THE TABLE ... 36

ADJUSTING THE BEVEL STOPS ..................................... 37

ADJUSTING THE BLADE HEIGHT.................................... 38

CHANGING THE BEVEL ................................................... 38

USING THE MITER GAUGE .............................................. 39

USING THE OUTFEED SUPPORT .................................... 39

USING THE RIGHT HAND TABLE EXTENSION ............... 40

RIP FENCE ADJUSTMENTS ............................................. 40

RIVING KNIFE POSITION AND ALIGNMENT ....................... 42

LOWERING RIVING KNIFE ............................................... 42

RIVING KNIFE ALIGNMENT .............................................. 43

MAINTENANCE ....................................................................... 45

TROUBLESHOOTING ............................................................. 45

ACCESSORIES ........................................................................ 45

WARRANTY ............................................................................. 46

FRENCH ................................................................................... 47

SPANISH ................................................................................... 93

Max depth of cut at 90 degrees: 3-1/2”

Max depth of cut at 45 degrees: 2-1/2”

Max rip to right of blade: 30”

Max rip to left of blade: 12”

Max width of dado: 13/16” x 8 dia.

MOTOR SPECIFICATIONS

Amps 15 Amps

VOLTAGE

120 Volts

FUNCTIONAL DESCRIPTION

The DELTA® #36-6022 series 10-inch Contractor

Table Saw is designed for portability and high quality

performance. It includes: basic machine, sturdy tubular

steel stand, integral 2 1/2” dust chute, a T-squared fence

system, T-slot miter gauge, 15-amp motor, on/off switch,

cast aluminum table, extension wing, see-through blade

guard with anti-kickback fingers, and 10-inch carbide

blade.

NOTICE: The manual cover illustrates the current production model. All other illustrations contained in the manual are

representative only and may not be exact depictions of the actual labeling or accessories included. They are intended for

illustrative purposes only.

SPECIFICATIONS

IMPORTANT SAFETY INSTRUCTIONS

SAFETY SYMBOLS- DEFINITIONS

This manual contains information that is important for you to know and understand. This information relates to protecting

YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the

symbols below. Please read the manual and pay attention to these sections.

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may

result in property damage.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

CAREFULLY READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS ON YOUR

PRODUCT AND IN THIS MANUAL. SAVE THIS MANUAL. MAKE SURE ALL USERS ARE

FAMILIAR WITH ITS WARNINGS AND INSTRUCTIONS WHEN USING THE TOOL. Improper operation, maintenance

or modification of tools or equipment could result in serious injury and/or property damage.

GENERAL SAFETY RULES

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

• READ INSTRUCTION MANUAL AND KNOW

YOUR TOOL. Read and familiarize yourself with

the entire instruction manual. Learning the tool’s

proper applications, limitation, and specific potential

hazards will greatly minimize the possibility of

accidents and injury. Make sure all users are familiar

with its warnings and instructions before using.

• MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Follow

instructions for lubricating and changing accessories.

• KEEP GUARDS AND SAFETY DEVICES IN PLACE

and working properly.

• CHECK TOOLS FOR DAMAGE. Before using,

and after tool or accessory has been dropped or

damaged, check guards and affected parts,

for alignment, breakage and any other condition

that may affect its operation to make sure tool will

operate properly and all parts will perform their

intended function. Do not use a damaged product.

A guard or any other part that is damaged should be

properly repaired or replaced using factory approved

service parts.

• NEVER STAND ON TOOL. Serious injury could

occur if the tool tips or if you unintentionally contact

the cutting surface.

• WEAR PROPER APPAREL. Do not wear loose

clothing, gloves, neckties, rings, bracelets, or other

jewelry which may get caught in moving parts.

Nonslip protective footwear is recommended. Wear

protective hair covering to contain long hair.

• WEAR PROPER EYE PROTECTION. All persons

in work area should wear safety glasses with side

shields. Everyday eye glasses with impact resistant

lenses are not safety glasses. Eye equipment should

comply with ANSI Z87.1 standards.

• WEAR PROPER HEARING PROTECTION. All

people in work area should wear proper hearing

protection consistent with noise levels and exposure.

Hearing equipment should comply with ANSI S3.19

standards.

• DUST PROTECTION. Use of power tools can

generate and/or disburse dust, which may cause

serious or permanent respiratory or other injury,

including silicosis (a serious lung disease), cancer,

and death. Direct particles away from face and body.

Always operate tool in a well-ventilated area and

provide for proper dust removal. Use dust collection

system whenever possible. Avoid breathing dust and

avoid prolonged contact with dust. Allowing dust to

get into your mouth or eyes, or lay on your skin may

promote absorption of harmful material. Use properly

fitting NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure and wash exposed

areas with soap and water.

• LOCK TOOLS AND WORK AREA. Use padlocks,

and master switches, or remove and store starter

keys to prevent operation by children and other

unauthorized users.

• DO NOT USE OR STORE TOOL IN DANGEROUS

ENVIRONMENTS. Exposure to rain and damp or

wet locations can result in shock or electrocution,

or damage the tool. Do not operate electric tools

near flammable liquids or in gaseous or explosive

atmospheres. Motors and switches in these tools

may spark and ignite fumes.

• KEEP WORK AREA CLEAN AND WELL LIT.

Cluttered and poorly-lit work areas, surfaces and

benches can lead to accidents.

4 5

GENERAL SAFETY RULES (CONTINUED)

• KEEP CHILDREN AND BYSTANDERS AWAY from

work area.

• USE RECOMMENDED ACCESSORIES. Consult

manual for recommended accessories. Use of

inappropriate accessories may cause personal injury

or property damage.

• DISCONNECT TOOL from power source before

servicing, adjusting or changing set-ups or blades,

bits, cutters and other accessories.

• TO REDUCE RISK OF ACCIDENTAL STARTING

make sure power switches are in “OFF” position

before plugging tool in.

• TO REDUCE THE RISK OF ELECTRIC SHOCK,

this equipment has a polarized plug (one blade is

wider than the other). This plug will fit in a polarized

outlet only one way. If the plug does not fit fully in the

outlet, reverse the plug. If it still does not fit, contact

a qualified electrician to install the proper outlet. Do

not change the plug in any way.

• DO NOT touch the plug’s metal prongs when

unplugging or plugging in the cord.

• USE PROPER EXTENSION CORD. If you use an

extension cord, make sure it is in good condition and

heavy enough to carry the current your product will

draw. An undersized cord will cause a drop in line

voltage, resulting in loss of power and overheating.

See Extension Cord Chart for correct size depending

on cord length and data plate ampere rating. If in

doubt, use the next smaller gauge number. The

smaller the gauge number, the heavier the cord.

When working outside, make sure the extension cord

is rated for outdoor use. Consult power connection

section of this manual for Extension Cord Chart and

power connection safety.

• DO NOT ABUSE POWER CORDS. NEVER yank

cord to disconnect from receptacle, crush cord, or

expose it to heat, oil or sharp objects.

• USE PROPER TOOL. Do not force tool to do a task

for which it was not designed.

• SECURE WORKPIECE. Use clamps or a vise to

hold the workpiece when practical. It is safer than

using your hands and frees both hands to operate

tool.

• REMOVE ADJUSTING KEYS AND WRENCHES.

Form habit of checking to see that all adjusting keys

and wrenches are removed before starting tool.

• STAY ALERT, WATCH WHAT YOU ARE DOING,

AND USE COMMON SENSE. Do not use power

tools when tired or under the influence of drugs,

alcohol, or medication. A moment of inattention while

operating power tools may result in injury.

• USE PROPER FEED DIRECTION. Feed workpiece

against the direction of rotation of the tool’s blade,

cutter, or abrasive surface. Feeding in the other

direction may cause the workpiece to be thrown at

high speed.

• DO NOT OVERREACH. Keep proper footing and

balance to maintain control.

• DO NOT FORCE TOOL OR WORKPIECE. Operate

tool at intended speed and feed rate for better and

safer operation.

• NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Do not leave tool until it comes

to a complete stop. In the event of a power failure,

move switch to “OFF” position.

• SERVICE PARTS. Use only identical replacement

parts when servicing your tool.

SAVE THESE INSTRUCTIONS.

Refer to them often and use them to instruct others.

If tool is loaned to someone, also loan them these instructions.

PROPOSITION 65 WARNING:

Dust created by power sanding, sawing, grinding, drilling, and other construction activities may contain

chemicals known to the state of California to cause cancer, birth defects or other reproductive harm.

Some examples are:

– Lead from lead-based paints

– Crystalline silica from bricks and cement and other masonry products

– Asbestos dust

– Arsenic and chromium from chemically-treated lumber

• Your risk from these exposures varies depending on how often you do this type of work. To reduce your exposure to

these chemicals: work in a well-ventilated area and work with approved safety equipment, such as dust masks that

are specifically designed to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap and water

If you have any questions or concerns relative to the use of your tool or the contents of this manual, stop using the tool

and call DELTA® Customer Care at 1-800-223-7278.

TABLE SAW SAFETY RULES

The following terms will be used throughout the manual and you should become familiar with them.

— Through-cut - any cut that completely cuts through

the workpiece.

— Non-through cut - any cut that does not completely

cut through the workpiece.

— Push stick - a wooden or plastic stick, usually

homemade, that is used to push a small workpiece

through the saw and keeps the operator’s hands

clear of the blade.

— Kickback - when the saw blade binds in the cut or

the workpiece binds between the blade and the

fence and the workpiece is thrust back toward the

operator.

— Freehand - cutting without the use of a miter gauge

or rip fence or any other means of guiding or holding

the workpiece other than the operator’s hand.

— Plunge cutting - blind cuts in the workpiece made

by either raising the blade through the workpiece or

lowering the workpiece down to the blade.

— Re-sawing - flipping the workpiece to complete a cut

the saw is not capable of making in one pass.

— Cove cutting - an operation where the work is fed at

an angle across the blade. (Also known as “coving”)

• AVOID KICKBACK. Pay particular attention to the

instructions (below) for reducing risk of kickback.

• OBTAIN ADVICE from your supervisor, instructor,

or another qualified person if you are not thoroughly

familiar with the operation of this machine.

Knowledge is safety.

• DRESS PROPERLY. Wear appropriate apparel, eye

protection, hearing protection and dust protection as

specified in the General Power Tool Safety Section of

this manual.

• PROPER ASSEMBLY. Do not operate this saw until

it is completely assembled and installed according to

the instructions.

• STABILITY. Make sure table saw is properly

assembled and located on a stable surface before

use to keep saw from moving during cut. Do not

attempt the subsitute a table or other surface for the

leg assembly.

• USE CORRECT BLADE AND RIVING KNIFE for the

intended operation. The blade must be installed so

the points of the teeth are pointing toward the front

of the saw. Do not use oversized blade or blade with

incorrect arbor opening. Always tighten the blade

arbor nut securely. Before use, inspect the blade for

cracks or missing teeth. Do not use a damaged or

dull blade. Always use blade within the thickness

range for which the riving knife is designed.

• USE PROPER THROAT PLATE. The proper throat

plate must be in place and properly secured at all

times to reduce the risk of a thrown workpiece and

possible injury.

• USE SAW BLADE GUARD, RIVING KNIFE AND

ANTI-KICKBACK PAWLS. Your saw is equipped

with a modular blade guard, riving knife and anti-

kickback pawl assembly, each component of

which should be used for every possible operation,

including all through cuts. This assembly is

discussed in more detail below. Make sure

components are securely installed prior to operation.

• NEVER CUT METALS, CEMENT BOARD OR

MASONRY. Certain man-made materials have

special instructions for cutting on table saws. Follow

the manufacturer’s recommendations at all times.

• SUPPORT YOUR WORKPIECE based on its size

and the type of operation to be performed. Hold the

workpiece firmly against the fence and down against

the table surface. Do not leave a wide panel or long

board (or other large workpiece) unsupported – the

weight of the workpiece may causes it to shift on the

table resulting in loss of control.

• NEVER PERFORM LAYOUT, ASSEMBLY OR SET-

UP WORK ON THE TABLE/WORK AREA when the

saw is running.

• USE A PUSH STICK that is appropriate to the

application to push and hold down a workpiece

through the completion of the cut. A push stick is

a wooden or plastic stick, usually homemade, that

should be used whenever the size or shape of the

workpiece would cause you to place your hands

within 6 in. (152 mm) of the blade. Instructions for

making a push stick are included in this manual. A

push stick is also provided with this saw.

• NEVER Perform freehand cutting, plunge cutting,

re-sawing, or cove cutting.

• CHECK WORKPIECE AND SET-UP before each

operation. Knots, irregularities, or nails in workpiece

and positioning mistakes or incomplete set-up may

interfere with or affect saw performance and personal

safety.

• NO FREEHAND CUTS. Always use a rip fence,

miter gauge, or other appropriate devices to guide

or hold down the workpiece. Use hold-downs, jigs,

fixtures or feather boards to help guide and control

The workpiece. Accessories for use with your saw

TERMINOLOGY

GENERAL POWER TOOL SAFETY

FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

• SEE GENERAL POWER TOOL SAFETY SECTION OF THIS MANUAL. Read entire instruction manual before

operating saw. Learning the saw’s proper applications, limitations, and specific potential hazards will greatly

minimize the possibility of accidents and injury. Make sure all users are familiar with its warnings and instructions

before using saw.

• SEE POWER CONNECTION SECTION OF THIS MANUAL for instructions and warnings regarding power

cords and connections.

6 7

TABLE SAW SAFETY RULES

Your table saw is equipped with a blade guard, anti-

kickback pawls and riving knife assembly that covers

the blade and reduces the possibility of accidental blade

contact. The riving knife is a flat plate that fits into the cut

made by the saw blade and effectively Figurehts kickback

by lessening the tendency of the blade to bind in the cut.

Two anti-kickback pawls are located on the sides of the

riving knife that allow the wood to pass through the blade

in the cutting direction but reduce the possibility of the

material being thrown backwards toward the operator.

The blade guard and anti-kickback pawls can only be

used when making through cuts that sever the wood.

When making rabbets and other non-through cuts, the

blade guard and anti-kickback pawls must be removed

and riving knife lowered to the non-through cut position

marked on the riving knife.

Use all components of the guarding system (blade

guard assembly, riving knife and anti-kickback pawls)

for every operation for which they can be used including

all through-cutting. If you elect not to use any of these

components for a particular application, exercise

additional caution regarding control of the workpiece, the

use of push sticks, the position of your hands relative to

the blade, the use of safety glasses, the means to avoid

kickback and all other warnings contained in this manual

and on the saw itself. Replace the guarding systems as

soon as you return to through-cutting operations. Keep

the guard assembly in working order.

In order to operate your table saw safely, you must use a

push stick whenever the size or shape of the workpiece

would otherwise cause your hands to be within 6 inches

(152 mm) of the saw blade or other cutter. A push stick is

included with this saw.

No special wood is needed to make additional push

sticks as long as they are sturdy and long enough and

the wood is free of knots, checks and cracks. A length

of 16 inches (400 mm) is recommended with a notch that

fits against the edge of the workpiece to prevent slipping.

It’s a good idea to have several push sticks of the same

minimum length, 16 inches (400 mm), with different size

notches for different workpiece thicknesses.

The shape can vary to suit your own needs as long as

it performs its intended function of keeping your hands

away from the blade. Angling the notch so the push stick

can be held at a 20- to 30-degree angle from the saw’s

table will help you to hold down the workpiece while also

moving it through the saw. Refer to diagram in cutting

aids section on page 26 of this manual.

MAKING A PUSH STICK

are available at extra cost from your local dealer or

authorized service center.

• DO NOT USE RIP FENCE AND MITER GAUGE AT

THE SAME TIME.

• AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause a

hand to move into a saw blade. Operate with table

at or near waist level for maximum balance and

control. Anticipate effect of workpiece size on your

ability to adjust position and maintain control through

completion of cut.

• KEEP ARMS, HANDS AND FINGERS AT LEAST

SIX INCHES AWAY FROM THE BLADE.

• KEEP HANDS AND OTHER BODY PARTS OUT OF

THE BLADE PATH. NEVER have any part of your

body in line with the path of the saw blade.

• NEVER START THE MACHINE WITH THE

WORKPIECE AGAINST THE BLADE to reduce the

risk of a thrown workpiece.

• DO NOT REACH OVER/REACH AROUND. Never

reach over, in back of, or around the cutting tool with

either hand while the blade is in motion.

• NEVER ATTEMPT TO FREE A STALLED BLADE

OR TRAPPED WORKPIECE without first turning

the machine off and disconnecting the saw from the

power source.

• BEFORE LEAVING THE SAW, wait for the blade to

come to a complete stop, then disconnect from the

power source, clean the table and work area, and

lock out switch to prevent unauthorized use.

• AN UNFAMILIAR NOISE OR EXCESSIVE

VIBRATION may indicate a problem with your saw.

If this happens, turn it off and disconnect it from the

power source until the problem has been located and

corrected. Contact customer service for assistance if

the problem cannot be solved.

SAW BLADE GUARD, ANTI-KICKBACK PAWLS AND RIVING KNIFE

ASSEMBLY

TABLE SAW SAFETY RULES

KICKBACKS

Kickbacks can cause serious injury. A kickback occurs

when a part of the workpiece binds between the saw

blade and the rip fence, or other fixed object, and rises

from the table and is thrown toward the operator. The

risk of kickback can be minimized by attention to the

following instructions.

HOW TO REDUCE THE RISK OF

KICKBACKS AND PROTECT YOURSELF

FROM POSSIBLE INJURY:

• Be certain that the rip fence is parallel to the saw

blade.

• DO NOT rip by applying the feed force to the section

of the workpiece that will become the cut-off (free)

piece. Feed force when ripping should always be

applied between the saw blade and the fence; use

a push stick for all narrow work that is 6 inches (152

mm) wide or less.

• Keep saw blade guard, riving knife and anti-kickback

assembly in place and operating properly. The riving

knife must be in alignment with the saw blade and

the anti-kickback assembly must stop a kickback

once it has started. Check their action before ripping

by pushing the wood under the anti-kickback

assembly. The teeth must prevent the wood from

being pulled toward the front of the saw. If any part

of assembly is not operational, return to the nearest

authorized service center for repair.

• Plastic and composite materials (like hardboard) may

be cut on your saw. However, since these are usually

quite hard and slippery, the anti-kickback pawls

may not stop a kickback. Therefore, be especially

attentive to following proper set up and cutting

procedures for ripping.

• Use saw blade guard, anti-kickback pawls, and riving

knife assembly for every possible operation, including

all through-cut sawing.

• Push the workpiece past the saw blade prior to

releasing control.

• NEVER rip a workpiece that is twisted or warped,

or does not have a straight edge to guide along the

fence.

• NEVER saw a large workpiece that cannot be

controlled.

• NEVER use the fence as a guide or length stop when

crosscutting.

• NEVER saw a workpiece with loose knots, flaws,

nails or other foreign objects.

• NEVER rip a workpiece shorter than 10 inches (254

mm).

• NEVER use a dull blade. A dull blade should be

replaced or re-sharpened.

8 9

POWER CONNECTIONS

This saw is equipped with a 15-amp motor for use with

a 120-volt, 60-HZ alternating current. See instructions

below regarding proper connections for your saw.

For voltage, the wiring in a shop is as important as the

motor’s rating. A line intended only for lights may not be

able to properly carry the current needed for a power tool

motor; wire that is heavy enough for a short distance may

be too light for a greater distance; and a line that can

support one power tool may not be able to support two

or three.

A separate electrical circuit should be used for your

machines. This circuit should not be less than #12 wire

and should be protected with a 20-amp time lag fuse.

Before connecting the machine to the power line, make

sure the switch is in the “OFF” position and be sure that

the electric current is of the same characteristics as

indicated on the machine. A substantial voltage drop will

cause a loss of power and overheat the motor. It may

also damage the machine.

POWER SOURCE

EXTENSION CORDS

Never use a damaged extension cord.

Check extension cords before each use.

If damaged, replace immediately. Touching the damaged

area could case electrical shock resulting in serious injury.

DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.

Keep the extension cord clear of the

work area. Position the cord so it will not

get caught on lumber, tools or other obstructions.

• Use proper extension cords. When using an

extension cord, be sure to use one heavy enough to

carry the current machine. An undersized cord will

cause a drop in line voltage, resulting in loss of power

and overheating. The table shows the maximum

gauge to use depending on the cord length. If in

doubt, use the next heavier gauge. The smaller the

gauge number, the heavier the cord. Only round,

jacketed cords listed by Underwriter’s Laboratories

(UL) should be used.

• When working with the tool outdoors, use an

extension cord designed for outside use.

MINIMUM GAUGE EXTENSION CORD

RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC

MACHINES

AMPERE

RATING

VOLTS TOTAL LENGTH

OF CORD IN

FEET

GAUGE OF

EXTENSION CORD

0-6

120

Up to 25

25-50

50-100

100-150

18 AWG

16 AWG

14 AWG

6-10

120

Up to 25

25-50

50-100

100-150

18 AWG

16 AWG

14 AWG

12 AWG

10-12

120

Up to 25

25-50

50-100

100-150

16 AWG

14 AWG

12 AWG

12-16 120 Up to 25 14 AWG

12-16 120 25-50 12 AWG

12-16 120

GREATER THAN 50 FEET NOT

RECOMMENDED

UNPACKING

A. Saw

B. Stand Handle

C. Wheels

D. Pedal Assembly

E. Right Support Rod

F. Left Support Rod

G. Support Rod Connection Tube

H. Cross Connect Assembly

I1. Upper Stand Assembly Part 1

I2. Upper Stand Assembly Part 2

J. T-Square Fence

K. 10 in. Carbide Tipped Blade

L. Miter Gauge

M. Blade Guard Assembly

N. Anti-Kickback Pawls

O. Throat Plate

The following items can be found

in their respective storage areas

located on the saw:

a. Blade wrenches (2)

b. Push Stick

PACKAGE CONTENTS DESCRIPTION (QTY)

• The machine is heavy, two people are required to

unpack and lift.

• Prior to tool assembly and use, read this manual

thoroughly to familiarize yourself with proper

assembly, maintenance and safety procedures.

Check shipping carton for damage before unpacking.

Carefully remove components in top foam layer. Remove

the top layer of foam then remove all components in

the bottom layer of foam. Lay out all parts on a piece

of cardboard or other clean, flat surface. Two or more

people are needed to lift the saw out of the carton.

Always check for and remove protective shipping

materials around motors and moving parts. Do not

discard shipping carton and packing materials until you

have carefully inspected the contents, assembled the

machine and are satisfied that it operates correctly.

Compare package contents to Component Parts List and

Hardware Package List prior to assembly to make sure

all items are present. Carefully inspect parts to make sure

no damage occurred during shipping. If any parts are

missing, damaged or preassembled, do not assemble.

Instead call DELTA® Customer Care at 1-800-223-7278

for assistance.

After assembly remove any protective materials and

coatings from all the parts and the table saw.

10 11

UNPACKING

ASSEMBLY

• Do not lift saw without help. Hold it close to your

body while lifting. Keep knees bent and lift with you

legs, not your back.

• Fully assemble saw with stand prior to use.

• Stand assembly is an integral and necessary part of

the support structure for this saw.

• Do not modify saw, or create accessories not

recommended for use with this saw.

• Make sure power switch is in “OFF” position before

connecting to power supply. Do not connect ti power

supply until assembly is complete.

• Avoid contact with blade teeth. Keep blade stored or

lowered when possible.

To measure fastener length, refer to page 7 of Parts List.

aa. M6 x 30 Hex Bolt (4)

bb. M8 x 67 Carriage Screw (4)

cc. Plastic Spacer (8)

dd. M8 Locknut (12)

ee. M8 x 75 Carriage Screw (4)

ff. M8 x 35 Carriage Screw (2)

gg. M8 x 30 Carriage Screw (2)

hh. 5mm Allen Wrench (1)

ii. M6 x 20 Button Head Hex Socket Screw (2)

jj. Wheel Handle Shoulder Screw (1)

kk. Height Adjustment Wheel Knob

ll. M8 x 55 Button Head Socket Screw (4)

mm. Fence Handle

CONTENTS OF HARDWARE BAGS

ASSEMBLY

FIGURE 1

FIGURE 2

ASSEMBLING UPPER STAND

Assemble upper half (I1) of upper stand assembly to lower half (I2) of upper stand assembly as shown in Figure 1 using

M8 x 75mm carriage screw (ee), spacer (cc) and M8 locknut (dd) to each side of upper stand assembly.

NOTE: I1 is attached to saw table assembly and secured with cable ties. Remove cable ties prior to assembling I1 and

I2.

NOTE: Orientation of I2 lock pin is on the right side of the assembly and orientation of I1 will have shoulder of tube

inserts on bottom as shown in Figure 2.

Finished upper stand assembly will appear as shown in Figure 2.

IMPORTANT: Tube insert shoulder on bottom.

LOCK PIN

TUBE INSERTS

SHOULDER

ON BOTTOM

TUBE INSERTS

SHOULDER

ON BOTTOM

12 13

ASSEMBLY

FIGURE 4

Secure the support rod assemblies to the support rod connect tube using two M8 x 30 Carriage bolts (gg) and M8 lock

nuts. (dd)

See Figure 4 & 4a.

FIGURE 3

ASSEMBLING THE STAND

Layout the left and right support rod assemblies (E & F).

Place the cross connect assembly (H) between the support rod assemblies and connect the support rod connection tube

(G) to the ends of the support rod assembly tubes as shown in Figure 3.

NOTE: Ensure foot pads are oriented as shown in Figure 3.

FOOT

PADS

FIGURE 5

Secure the cross connect assembly (H) to the support rod assembly tubes using four M6 x 30 hex bolts. (aa)

See Figure 5 & 5a.

ASSEMBLY

FIGURE 6

WHEELS

Remove the lock nut and washer from each axle on the pedal assembly (D) as shown in Figure 6.

14 15

ASSEMBLY

FIGURE 7

PEDAL ASSEMBLY

Slide the wheels over axles and secure using the two washers and M8 lock nuts.

See Figure 7.

Attach the pedal assembly (D) to the upper stand assembly using two M8 x 75 Carriage screws (ee), spacers (cc)

and M8 lock nuts (dd). See Figures 8 & 9 to verify the correct orientation of the pedal assembly (C) to the upper stand

assembly.

FIGURE 8

UPPER

STAND

ASSEMBLY

FIGURE 10

E F

ASSEMBLY

UPPER

STAND

ASSEMBLY

SEE FIGURE

FIGURE 9

Place the sides of the support rod assembly (E & F) so they are outside of the pedal assembly (D) and the feet are

pointing down. See Figure 11 for correct position of the feet.

Align the hole in the support rod assembly with the hole in the pedal assembly. See Figure 10.

Secure each side of the support rod assembly using two M8 x 67 carriage bolts (bb), spacers (cc) and M8 lock nuts (dd).

See Figures 10 & 11.

NOTE: At any time, to aid in assembly, refer to front cover of this manual for completed saw.

16 17

ASSEMBLY

FEET

SEE

FIGURE

FIGURE 11

UPPER STAND ASSEMBLY

Insert the stand handle (B) into the upper stand assembly as shown in Figure 12.

Insert M8 x 35 carriage screw (ff) into the square hole at the end of the upper stand assembly (square hole at end of tube

see Figure 12a) secure carriage screw (ff) with M8 Locknut (dd). Repeat this step on the other side of the handle.

FIGURE 12

UPPER

STAND

ASSEMBLY

Attach the right and left support rod assemblies (E & F)as shown in Figure 13 to the upper stand assembly with two M8 x

67 carriage screws (bb), spacer (cc) and M8 locknuts (dd) as shown in Figures 13 & 14.

NOTE: Ensure the spacer (cc) is between the support rod assembly and the upper stand assembly as shown in Figure

13.

NOTE: Make sure all hardware is tight but not overtight. The amount of tightening applied to pivoting joints will affect the

stand operation.

Correct stand assembly will appear as shown in Figure 14.

FIGURE 13

UPPER

STAND

ASSEMBLY

SEE

FIGURE

FIGURE 14

E F

18 19

SAW

STAND

ASSEMBLY

FIGURE 16

Place saw on stand and align threaded holes in saw with through holes on stand secure with four M8 x 55 button head

socket screws (ll).

See Figure 16.

FIGURE 15

ATTACH SAW TO STAND ASSEMBLY

Unlock the bevel lock tilt and rotate the motor assembly enough to remove the shipping foam protecting the saw motor

as shown in Figure 15.

Do NOT turn the handwheel during this step.

BLADE AND GUARDS

Attach the Blade

After installing height adjustment knob as shown in Figure. 17, raise motor/arbor assembly to the upper

most position to provide easy access to riving knife lock lever and arbor assembly.

Ensure riving knife lock lever is in unlock position. See Figure. 18.

Detach the on-board wrenches located on the right side of the saw by loosening and removing M8 wing

nut.

Place the open-ended wrench (a) on the spindle shoulder between the arbor flange and inner flange.

Place the closed end wrench (a) over the arbor nut. Holding the spindle shaft in place, loosen and remove

the arbor nut and arbor flange.

See Figure 18.

FIGURE 18

FIGURE 17

1. Insert wheel handle shoulder screw (jj) into height adjustment wheel knob (kk) as shown in Figure. 17.

2. Tighten shoulder screw with Phillips Screw Driver into the Hand Wheel. Height adjustment wheel knob should rotate

freely around shoulder screw when raising or lowering the blade with the Height Adjustment Hand Wheel.

Height Adjustment Knob Installation

UNLOCK

POSITION

CLOSED END

WRENCH

ASSEMBLY

20 21

ASSEMBLY

FIGURE 19

TOOTH

DIRECTION

FRONT OF

SAW

ARBOR

SHAFT

FIGURE 20

Place blade (K) on the arbor shaft with the teeth on the blade pointing toward the front of the saw. Place flanged washer

on the shaft with the large side of the washer against the blade, then secure blade assembly with nut. (Figure. 19)

Tighten nut with blade wrenches (a). Open end wrench will fit on the arbor shaft between the inner flange washer and the

motor assembly (if neccessary, turn arbor shaft to align flats on the arbor shaft to the wrench). Closed end wrench will fit

on the nut. See Figure 20.

Return wrenches (a) to onboard storage location. Position the riving knife in the “Thru-cut” position prior to installation of

thoat plate.

Details for positioning the riving knife are on page 32 RIVING KNIFE POSITION AND ALIGNMENT Section.

See Figure 21.

ASSEMBLY

Insert Throat Plate

Refer to Figure 22.

Place the throat plate (O) in place with the wear plate on the rear.

Engage the rear tab on the throat plate under the table and press the front end down until the front tab snaps into place

on the table.

To reduce the risk of serious injury,

• the riving knife must be installed for every through cut and for every non-through cut unless the riving knife would

interfere with the cut.

• always use a blade with the correct thickness to match the riving knife. (0.10” (2.6mm) min. kerf width and 0.073”

(1.85mm) max body thickness)

• The riving knife must be securely positioned in the “up” or “through cut” position when using the antikickback pawls

and blade guard.

• Make sure the riving knife is properly aligned to the blade. (See Riving Knife Position and Alignment, Page 33.

LOCK

POSITION

RIVING

KNIFE

THRU CUT

POSITION

FIGURE 21

FIGURE 22

WEAR

PLATE

22 23

ASSEMBLY

Level the throat plate to the table top using (4) flat head screws. See Figure 23 and 24. For more details about leveling

throat plate, see page 29.

NOTE: There is a fifth flat head screw under the throat plate that is adjusted to provide support under the wear plate.

Adjust this screw as needed to provide support.

To reduce risk of serious injury, do not attempt to secure the throat plate to the table using the throat

plate leveling screws.

FIGURE 23

FIGURE 24

SCREW UNDER

THROAT PLATE

Anti-Kickback Pawls and Blade Guard

Press spring loaded pin on the right side of the anti-kickback pawl assembly (N) insert over the middle slot on the riving

knife.

Once inserted, release the spring-loaded pin so that it pops back into place. Ensure it is locked in place by gently pulling

up on the anti-kickback pawl assembly (N).

FIGURE 26

FIGURE 25

FIGURE 27

SUPPORT

ARMS

RIVING

KNIFE

PRESS

LOCK

TAB

Hold the blade guard assembly (M) as shown in Figure 26 and engage the pin with the slot in the riving knife. Pull blade

guard assembly up into place.

Rotate the blade guard so that the support arms are parallel to the table. Then lock the blade guard in place by

depressing the lock tab.

Verify the Blade Guard Assembly is properly locked in place. Do this by gently lifting up on the support arms after the

lock tab has been depressed. If blade guard is not properly locked onto the riving knife, support arms will raise up and

lock tab will spring up to the unlocked position.

See Figure 27.

To reduce risk of serious injury. It is important that you do not use the table saw if blade guard assembly

is not locked into place on the riving knife.

ASSEMBLY

24 25

ASSEMBLY

Assemble handle (mm) to fence assembly (J) as shown in Figure 29.

FIGURE 29

Outfeed Support Stops

Refer to Figure 28.

Extend the rear table support to expose the two holes. Insert an M6 x 20 button head hex socket screw (ii) from

underneath, tighten with the supplied allen wrench.

Repeat on other side of outfeed suport.

FIGURE 28

ASSEMBLY

Position the T-square fence (J) over the front and rear rails. Ensure the fence lock is in the unlocked (up) position.

Lower T-square fence (J) on to both front and rear rails. Position T-square fence (J) on the table as desired and lock into

place.

See Figure 30.

FIGURE 30

LOCKED

POSITION

26 27

ASSEMBLY

FIGURE 31

CORD

WRAP

FIGURE 32

ON-BOARD STORAGE

Storage is located on the left panel, right panel and back side of the tool as shown in Figures 31 & 32.

b. Push Stick

N. Anti-kickback assembly

a. Wrenches

M. Blade guard assembly

J. Fence

L. Miter gauge

Electrical Cord wrap

NOTE: Prior to placing the rip fence in the storage position you must temporally remove the miter gauge from the

storage position.

OPERATION

READ ENTIRE MANUAL. In addition to reading these operating instructions, it is important to read and understand

the entire manual before operating this saw. Follow all applicable instructions regarding assembly, preparation, and

adjustment prior to making any cuts and comply with all safety rules and warnings in this section and elsewhere

throughout this manual.

1. Each time you use the saw, run through the

following checklist:

• Are the power source and power connections

adequate for the saw?

• Are the saw and work area free of clutter and

by-standers?

• Is the blade tight and properly aligned?

• Does the riving knife thickness match the blade?

• Are the blade and riving knife properly aligned?

• Is the operator qualified to make the cut and familiar

with all of the relevant safety rules, warnings and

instructions included in this manual?

• Is the operator and everyone in proximity to the saw

wearing appropriate eye, hearing and respiratory

equipment?

• Are the bevel angle and height adjustment knobs

locked in the proper position?

• Is the blade set at the proper height?

• If ripping, is the rip fence parallel to the blade and

securely locked in place?

• If crosscutting, is the miter gauge knob too tight?

• If making through cuts with a standard blade, are

the blade guard riving knife and anti-kickback pawls

properly attached and properly functioning with both

guards contacting the table surface?

• Is there proper clearance and support for the

workpiece as it leaves the blade?

• Are any cutting aids needed? If so, are they in place,

or within reach for proper use?

2. The use of attachments and accessories not

recommended by DELTA® Power Equipment

Corporation may result in injury.

3. Replace or sharpen the anti-kickback fingers

when the points become dull.

4. Make sure saw is stable and cutting can be

accomplished without tipping the saw.

5. Never use the fence and miter gauge together

without using a cutoff block as previously

described.

6. The proper throat plate must be in place at all

times.

7. If your saw makes an unfamiliar noise or if it

vibrates excessively, cease operating immediately

until the source has been located and the

problem corrected.

8. Never perform freehand cutting, plunge cutting,

re-sawing or cove-cutting.

AVOID KICKBACK

A kickback can occur when the workpiece pinches the

blade, or binds between the saw blade and the rip fence

or other fixed object. This can cause the workpiece

to rise from the table and/or be thrown back toward

the operator. See instructions for reducing the risk of

kickback in page 7 of this manual.

IF KICKBACK OCCURS, turn the saw “OFF” and verify

proper alignment of the blade, riving knife and miter

gauge or rip fence, and the proper functioning of the

riving knife, anti-kickback assembly and blade guard

before resuming work.

Failure to follow these rules may result in serious personal injury.

28 29

OPERATION

To fold stand for moving, return side and rear extension tables to inner position lock side extension into place. Stow rip

fence and miter gauge. Grasping handle bar, push the stand release pedal with foot and tilt up and forward until the saw

rests on the wheels and stand feet.

See Figures 34 & 35.

TRANSPORTING THE SAW

FIGURE 34 FIGURE 35

FIGURE 33

LOCK

OUT

OFF

The ON/OFF paddle switch is located on the left side of the front panel of the saw.

To turn the saw ON lift the switch. Press the switch down to turn the saw OFF.

When not in use, the saw should be turned off and the power switch locked out to prevent unauthorized use. To lock out

power switch, use a standard long shackle lock, with a shackle posts no larger than 9/32-inch (7mm) thick.

See Figure 33.

TURNING THE SAW ON AND OFF

MAKING CUTS

Failure to comply with the following

warnings may result in serious

personal injury.

• Never touch the free end of the workpiece or a free

piece that is cut off, while the power is on and/or the

saw blade is rotating. Blade contact or binding may

occur, resulting in a thrown workpiece.

• When sawing a long workpiece or a panel, use a

work support, such as a sawhorse, rollers or outfeed

table at the same height as the table surface of the

saw.

• Never try to pull the workpiece back or lift it off the

table, turn the switch off, allow the blade to stop,

raise the anti-kickback teeth on each side of the

riving knife if necessary, and slide the workpiece out.

• Before connecting the table saw to the power source

or operating the saw, always inspect the blade guard

assembly and riving knife for proper alignment and

clearance with the saw blade. Check alignment after

each change of beveling angle.

• A rip fence should ALWAYS be used for ripping

operations to prevent loss of control and personal

injury. Always lock the fence to the rail. NEVER

perform a ripping operation freehand.

• When making bevel cuts, place the fence on the right

side of the blade so that the blade is tilted away from

the fence and hands. Keep hands clear of the blade

and use a push stick to feed the workpiece unless

the workpiece is large enough to allow you to hold it

more than 6 inches (152 mm) from the table.

• Before leaving the saw unattended, lock out power

switch, or take other appropriate measures to

prevent unauthorized use of the saw.

Cross Cut

Beveled Cross Cut Beveled Rip Cut

Compound Miter Cut

Mitered CrosscutRip Cut

30 31

MAKING CUTS

1. Remove miter gauge.

2. Make sure bevel angle is set to 0º.

3. Set blade to correct height for workpiece.

4. Install rip fence and lock it down parallel with and at

desired distance from blade.

5. Keep fingers at least 6 inches from the blade at

all times. When the hand cannot be safely out

between the blade and the rip fence, select a larger

workpiece, or use a push stick and other cutting

aids, as needed, to control the workpiece.

6. Make sure the workpiece is clear of the blade (at

least 1 inch or 25 mm away) before starting the saw.

7. Turn saw on.

8. Hold the workpiece flat on the table and against the

fence (A). The workpiece must have a straight edge

against the fence and must not be warped, twisted

or bowed. See proper hand position in Figure 36.

9. Let blade build up to full speed before moving

workpiece into the blade.

10. Both hands can be used while starting the cut as

long as hands remain 6 inches from the blade.

11. Keep the workpiece against the table and fence

and slowly feed the workpiece rearward all the way

through the saw blade. Do not overload the motor by

forcing the workpiece into the blade.

12. Use the push stick and any other cutting aids, as

needed, to hold the workpiece against the table and

fence, and push the workpiece past the blade. A

push stick is included with this saw, and instructions

are included to make additional push sticks and

other cutting aids.

13. Do not push or hold onto the free or cut-off side of

the workpiece.

14. Continue pushing the workpiece until it is clear of

the blade. Do not overload the motor by forcing the

workpiece into the blade.

15. When cut is complete, turn saw off. Wait for blade to

come to a complete stop before removing workpiece

from table.

Bevel ripping is the same as ripping except the bevel

angle (A) is set to an angle other than 0. When making

a bevel rip cut, place the fence on the right side of the

blade so that the blade is tilted away from the fence and

hands.

See Figure 37.

RIP CUTS

BEVEL RIPPING

FIGURE 36

FIGURE 37

MAKING CUTS (CONTINUED)

CROSSCUTTING

BEVEL CROSSCUTTING

MITER CUTS

Bevel crosscutting is the same as crosscutting except

the bevel angle (A) is set to an angle other than 0°. When

making a bevel crosscut, place the miter gauge in the

right miter slot so that the blade is tilted away from the

gauge and hands. See Figure 39.

Miter cuts are cross cuts with the miter gauge set at an

angle other than 90°. Miter gauge can be adjusted to one

of the 8 positive stop angles or as desired to an individual

angle increment.

• Miter angles more than 45˚ may force the blade

guard assembly into the saw blade causing damage

to the blade guard assembly and personal injury.

Before starting the motor, test the operation by

feeding the workpiece into the blade guard assembly.

If the blade guard assembly contacts the blade,

place the workpiece under the blade guard assembly

but not touching the blade - before starting the

motor.

• Certain workpiece shapes, such as molding may

not lift the blade guard assembly properly. With

the power off, feed the workpiece slowly into the

blade guard area and until the workpiece touches

the blade. If the blade guard assembly contacts the

blade, place the workpiece under the blade guard

assembly - but not touching the blade - before

starting the motor.

FIGURE 38

FIGURE 39

• NEVER use the fence as a guide or length stop

when crosscutting, unless you are using the fence as

described on page 28 Figure 46 of this manual.

• The cut-off piece must never be confined in any

through-sawing (cutting completely through the

workpiece) operation—to prevent pinching blade

which may result in a thrown workpiece and possibly

injury.

• When using a block as a cut-off gauge, the block

must be at least 3/4-inch (19mm) thick. It is very

important that the rear end of the block be secured in

a position where the workpiece is clear of the block

before it enters the blade to prevent binding of the

workpiece.

You can use the miter gauge in either table slot on non-

bevel cuts. To increase surface area of miter gauge face,

add an auxiliary face (See Cutting Aids section on page

27 of this manual.)

To make a crosscut, refer to Figure 38 and follow this

process:

1. Remove rip fence.

2. Make sure bevel angle is set to 0°.

3. Set blade to correct height for workpiece.

4. Place miter gauge in either miter slot.

5. Set miter gauge to 90° and tighten miter gauge lock

knob

6. Hands must remain at least 6 inches from blade

throughout entire cut. If workpiece is too small to

keep hands at least 6 inches away from the blade,

select a larger workpiece, or attach an auxiliary face

to the miter gauge and attach workpiece to auxiliary

face, For instructions about making auxiliary faces,

see Cutting Aids section on page 27 of this manual.

7. Make sure the workpiece is clear of the blade - at

least 1 inch or 25mm away - before starting the saw.

8. Turn saw on.

9. Let blade build up to full speed before moving

workpiece into the blade.

10. Hand closest to blade should be placed on miter

gauge lock knob and hand farthest from blade

should hold workpiece firmly against the miter gauge

face. Do not push or hold onto the free or cut-off side

of the workpiece.

11. Slowly feed the workpiece rearward all the way

through the saw blade. Do not overload the motor by

forcing the workpiece into the blade.

12. When cut is complete, turn saw off. Wait for blade

to come to a complete stop before removing cut off

piece from table.

32 33

MAKING CUTS (CONTINUED)

COMPOUND MITER CUTS

LARGE PANEL CUTS

This is a combination of bevel crosscutting and mitering.

Refer to Figure 40 and follow the instructions for both

bevel crosscutting and mitering. Remember to use the

right miter slot on the right side of the blade for all bevel

cuts.

Place workpiece supports at the same height as the

saw table behind saw to support the cut workpiece, and

alongside (s) of saw, as needed. Depending on shape of

panel, use rip fence or miter gauge to control workpiece.

If a workpiece is too large to use either a rip fence or a

miter gauge, it is too large for this saw.

NON-THROUGH CUTS

MAKING A NON-THROUGH CUT

The use of a non-through cut is essential to cutting

grooves, and rabbets. Non-through cuts can be made

using a standard blade having a diameter of 10 inches.

Non-through cuts are the only type of cuts that should

be made without the blade guard assembly installed.

Make sure the blade guard assembly is reinstalled upon

completion of this type of cut.

• When making non-through cuts, follow all applicable

warnings and instructions listed below in addition to

those listed above for the relevant through cut.

• When making a non-through cut, blade is covered by

workpiece during most of cut. Be alert to exposed

blade at start and finish of every cut.

• Never feed wood with hands when making any non-

through cuts such as rabbets or grooves. Always

use miter gauge, push blocks or push sticks, and

featherboards where appropriate.

• In addition to this section, read the appropriate

section which describes the type of through or cut.

For example, if your non-through cut is a straight

cross cut, read and understand the section on

straight cross cuts before proceeding.

• Once all non-through cuts are completed, unplug

saw and return riving knife to through cut position.

Install anti-kickback pawls and blade guard.

• Carefully follow the instructions accompanying any

specialized blades for proper installation, set up and

operation.

1. Unplug saw.

2. Unlock bevel lock.

3. Adjust bevel angle to 0°.

4. Lock bevel lock.

5. Remove blade guard and anti-kickback pawls.

6. Place riving knife in “lowered” position. See RIVING

KNIFE POSITION AND ALIGNMENT Section on page

32.

7. Set blade to correct depth for workpiece.

8. Depending on shape and size of wood, use either rip

fence or miter gauge.

9. Plug saw into power source and turn saw on.

10. Let blade build up to full speed before moving

workpiece into blade.

11. Always use push blocks, push sticks, and/or

featherboards when making non-through cuts to

reduce the risk of serious injury.

12. When cut is made, turn saw off. Wait for blade to

come to a complete stop before removing workpiece.

FIGURE 40

CUTTING AIDS AND ACCESSORIES

MAKING CUTS

PUSH STICK

In order to operate your table saw safely, you must use a

push stick whenever the size or shape of the workpiece

would otherwise cause your hands to be within 6-inches

(152mm) of the saw blade or other cutter. A push stick is

included with this saw.

No special wood is needed to make additional

pushsticks as long as it is sturdy and long enough with

no knots, checks or cracks. A length of approximately 16

inches (400mm) is recommended with a notch that fits

against the edge of the workpiece to prevent slipping.

It’s a good idea to have several push sticks of the same

minimum length, 16 inches (400mm), with different size

notches for different workpiece thicknesses.

The shape can vary to suit your own needs as long as

it performs its intended function of keeping your hands

away from the blade. Angling the notch so the push stick

can be held at a 20 to 30-degree angle from the saw’s

table will help you to hold down the workplace while also

moving the saw.

To construct a push stick, refer to the layout shown in

Figure 42.

MAKING A DADO CUT

Dado blades are stacked blades that can be used when

making non-through cuts including through cut slots.

Dado blades require a special throat plate. Dado blades

and throat plates are all sold separately.

• Carefully follow the instructions accompanying

the dado blade for proper installation, set up

and operation. Additional guides can be found

in woodworking and carpentry websites and

publications.

• Do not attempt to stack dado blades thicker than

13/16 inch (20.64 mm). Do not use dado blades

larger than 8-inches (200 mm) in diameter.

• The riving knife and blade guard assemblies cannot

be used when dadoing. They must be removed

as described in Riving Knife and Blade Guard

Operations section. Use EXTREME care when using

the dado without the blade guard assembly and

riving knife.

• Use push sticks, hold-downs, jigs, fixtures or feather

boards to help guide and control the workpiece when

the guard cannot be used.

• Be sure to reinstall the riving knife, anti-kickback

pawls blade guard and standard throat plate,

and check adjustments when the dado cuts are

complete.

• The accessory dado head set throat plate, shown in

Figure 41, must be used in place of the standard

throat plate. Be sure the throat plate is level to the

table before you proceed.

• Always check the dado blade clearance with other

components before plugging in the saw.

• Never attempt to use the dado head in a bevel

position.

NOTE: The standard outer arbor flange cannot be used

with certain dado blade combinations. In those cases,

tighten the arbor nut directly against the dado blade set.

Save the outer arbor flange for use with other blades and

dado combinations.

FIGURE 42

FIGURE 41

34 35

CUTTING AIDS AND ACCESSORIES (CONTINUED)

AUXILIARY MITER GAUGE

FACING

PUSH BLOCK

An auxiliary miter gauge facing is used to increase the

surface area of the miter gauge face.

If desired, you can fit the miter gauge with an auxiliary

wood facing that should be at least 1-inch (25mm) higher

than the maximum depth of cut, and at least as wide as

the miter gauge.

This auxiliary wood facing can be fastened to the front

of the miter gauge by using (2) M6 or 1/4-20 flat head

screws and nuts, placing the nuts into the slots provided

in the face of the miter gauge body.

See Figure 43.

Make sure the screws are long enough to secure the

facing.

Flat head must be recessed into face of

board.

1. Select a piece of wood about 4-inches wide,

6-inches long and 1- to 2-inches thick (a cutoff from

a 2 by 4 makes a good blank for a push block).

2. Drill a hole in the block and glue in a dowel to use as

a handle (you can angle the hole to provide a more

comfortable grip on the handle).

3. Glue a piece of rough or soft material such as

sandpaper or rubber to the bottom of the block to

grip the workpiece (old mouse pads work well).

See Figure 44.

FIGURE 43

FIGURE 44

CUTTING AIDS AND ACCESSORIES (CONTINUED)

FEATHERBOARD

CUT OFF GAUGE

JIGS

When crosscutting a number of pieces to the same

length, you can clamp a block of wood (A) (See Figure 46)

to the fence and use it as a cut-off gauge. The block (A)

must be at least 3/4-inch (19 mm) thick to prevent the cut

off piece from binding between the blade and the fence.

Once the cut-off length is determined, lock the fence and

use the miter gauge to feed the workpiece into the blade.

Always position the entire cut-off

gauge in front of the saw blade.

FIGURE 45

FIGURE 46

Featherboards are used to keep the workpiece in contact

with the fence and table (Figure 45), and help prevent

kickback. Featherboards are especially useful when

ripping small workpieces and for completing non-through

cuts. The end is angled with a series of narrow slots to

give a friction hold on the workpiece, It is locked in place

on the table or fence with a c-clamp.

To avoid binding between the

workpiece and the blade, make sure

a horizontal feather board presses only on the uncut

portion of the workpiece in front of the blade.

Dimensions for making a typical featherboard are shown

in Figure 45 . Make your featherboard from a straight

piece of wood that is free of knots and cracks. Clamp

featherboards to the fence and/or table so that the

featherboard will hold the workpiece against the fence or

table.

1. Select a solid piece of lumber approximately 3/4-inch

thick, 2 1/2-inches wide and 12-inches long.

2. Mark the center width on one end of stock. Miter

width to 70° (see miter cut section for information on

miter cuts).

3. Set rip fence to allow approximately a 1/4-inch

“finger” to be cut in the stock.

4. Feed stock only to mark previously made at 6 inches.

5. Turn saw off and allow blade to completely stop

rotating before removing stock.

6. Reset rip fence and cut spaced rips into workpiece

to allow approximately 1/4-inch fingers and 1/8-inch

spaces between fingers.

Jigs may be created with a variety of special set-ups

to control particular workpiece shapes for particular

cuts. Guidance on how to make specialized jigs can

be found in woodworking and carpentry websites and

publications.

Do not attempt to create or use a jig

unless you are thoroughly familiar with

table saw safety. Do not use any jig that could result

in pinching a kerf or jamming the workpiece between

the jig and the blade. Incorrect setups may cause

kickback which could result in serious injury.

36 37

MAKING ADJUSTMENTS

LEVELING THE THROAT PLATE

SQUARING THE BLADE VERTICALLY TO THE TABLE

The front, rear and sides of the throat plate must be level with the surface of the table.

There are four screws pre-assembled to the table that are used to level the throat plate.

If the throat plate is not flush with the surface of the table, adjust these screws to ensure the entire throat plate is flush

with the table. They can be accessed and adjusted without removing the throat plate. Do not attempt to mount the throat

plate down using the throat plate leveling screws.

See Figures 47 & 47a.

Place a framing square (B) on the table surface and against both blade and riving knife. The framing square should be in

full contact with the blade face and riving knife.

See Figure 48.

If it is not square, adjust the 0-degree stop as shown in “Adjusting The Bevel Stops” below.

See Figures 49, 49a, 50 and 50a.

FIGURE 47

FIGURE 48

SCREW UNDER

THROAT PLATE

ADJUSTING THE BEVEL STOPS

If the blade is not vertically square with the table, you must adjust the 0-degree positive stop located on the inside of

the bevel track at the left end of the bevel track opening as shown in Figures 50 and 50a.

Unlock the bevel/height adjustment locking lever and position the adjustment wheel to the right in order to gain easy

access to the 0-degree positive stop. Then lock the adjustment lever.

Turn the 0-degree positive stop set screw to right or left to adjust stop location.

Unlock the adjustment wheel, return the blade to the 0-degree position, making sure it makes contact with the

positive stop, and re-lock the adjustment wheel in place.

Recheck the position of the blade to the table surface using a framing square (See “SQUARING THE BLADE

VERTICALLY TO THE TABLE” ON THIS PAGE).

Continue repeating previous two steps until the blade is vertically square to the table.

You can use this same procedure in order to check the 45-degree positive stop, located at the far right end of the

bevel track, just inside the bevel track opening as shown in Figures 49 & 49a.

FIGURE.

FIGURE 49

FIGURE 50

45°

0°

UNLOCK

LOCK

MAKING ADJUSTMENTS

38 39

MAKING ADJUSTMENTS

ADJUSTING THE BLADE HEIGHT

CHANGING THE BEVEL

For all through cuts, the top of the blade points should be above the workpiece and the bottom of the blade gullets are

below the top surface of workpiece.

For non-through cuts, the top of the blade points should be set to the depth of the cut.

To adjust the height of the blade, refer to Figure 51 and do the following:

Make sure the bevel/height adjustment locking lever is in the locked position.

Adjust the blade height by turning the bevel/height adjustment wheel. Clockwise will raise the blade and

counterclockwise lowers it.

Unlock the bevel/height adjustment locking lever by pulling it into the unlock position.

Holding knob/wheel, slide the bevel indicator to the desired angle.

When the blade is at desired angle, lock the bevel/height adjustment locking lever by pushing it down to the lock

position.

See Figure 51.

FIGURE 51

ADJUSTMENT

WHEEL

LOCKING

LEVER

UNLOCK

LOCK

MAKING ADJUSTMENTS

USING THE MITER GAUGE

USING THE REAR OUTFEED SUPPORT

There are two miter gauge grooves. one on either side of the blade. When making a 90º cross cut, use either groove. For

beveled cross cut use the groove on right so that the blade is tilted away from miter gauge and hands.

Loosen the miter gauge lock knob. Rotate the gauge until desired angle on scale is reached. Retighten lock knob.

See Figure 52.

The out-feed support slides out to provide additional support for cutting long work pieces.

Ensure the power switch is in the OFF position. From the rear of the saw, grasp the out-feed support with both hands

until it is fully extended.

See Figure 53.

FIGURE 52

LOCK

KNOB

FIGURE 53

40 41

MAKING ADJUSTMENTS

USING THE RIGHT HAND TABLE EXTENSION

RIP FENCE ADJUSTMENTS

The table extension, located on the right side of the table, enables you to increase the width of the saw table to

accommodate oversized workpieces.

To use the table extension, refer to Figure 54 and do the following:

Release the table extension lock (B) by moving it up. Slide side table extension out to the right. Use the blue pointer on

the top scale to determine desired distance. When extension table is set to desired width, push lock lever to the lock

position.

To adjust rip fence so it is parallel to the blade, make adjustments to the set screws on the front of the fence as shown in

Figure 55.

FIGURE 54

EXTENSION

TABLE

POINTER

UNLOCK

LOCK

FIGURE 55

HEX

WRENCH

SET SCREW

To adjust the rip fence so it is perpendicular to the table, make adjustments to the nylons screws on the top of the rip

fence “T” as shown in Figure 56.

FIGURE 56

To make adjustments to clamping pressure for rip fence, adjust screw on back of fence to the right to tighten and to the

left to loosen clamping pressure.

See Figures 57 & 57a.

MAKING ADJUSTMENTS

FIGURE 57

42 43

LOWERING THE RIVING KNIFE

Remove throat plate.

1. With the blade assembly to the highest possible position, carefully reach alongside the blade and raise the riving

knife locking lever up to unlock the riving knife.

2. Gently move the riving knife to the right to release it from the lock pins in the riving knife assembly.

3. Slide the riving knife down and backward until you feel the lock pins engage the riving knife in the “Non-Thru

Cut” position. When properly aligned in this position, the “Non-Thru Cut” line on the riving knife will be parallel to

and level with the table. See Figure 59 on page 33.

4. Return the riving knife lock lever to the lock position.

5. Make sure the riving knife is securely installed and properly aligned with the blade.

To raise riving knife to “Thru-Cut” position repeat steps 1-5 and on step 3 raise riving knife up and forward.

Reinstall throat plate.

FIGURE 58

UNLOCK

LOCK

RIVING KNIFE POSITION AND ALIGNMENT

Location point for NON-THRU CUT POSITION

NOTE: Riving knife is located in this position for “NON-THRU” cuts and is also in this position when packaged for

shipment.

Location point for THRU CUT POSITION as shown in Figure 59. (Operator should adjust the riving knife to this position

when making “THRU” cuts.)

(NOTE: You must locate the riving in THRU CUT position prior to making any alignment adjustments to the riving knife

alignment to the blade.)

The plane of the riving knife is parallel to the plane of the blade but the riving knife and the blade are not in line with

each other.

If a parallel adjustment is required use Figure 59 and Figure 60 to make the following adjustments:

1. Loosen the two hex socket head screws (AA)

2. Tighten or loosen the adjustment screw (BB1) to adjust the datum line of the riving knife to be aligned with the

blade.

3. Adjust set screw (BB2) and (BB3), to assist with the alignment of the riving knife to be parallel to the blade.

4. Tighten hex socket head screws (AA).

FIGURE 59

NON-THRU

CUT

THRU-CUT

BB1

BB2

BB3

FIGURE 60

RIVING KNIFE ALIGNMENT

Parallel Alignment

44 45

RIVING KNIFE POSITION AND ALIGNMENT

The plane of the riving knife appears to be twisted in comparison to the plane of the blade from the bottom of the riving

knife to top of the riving knife. (Can be seen looking from the front of the saw.)

If the riving knife has vertical misalignment, adjust as follows using Figure 59 and Figure 62.

1. Loosen the two hex socket head screws (AA)

2. Make adjustments to (BB2) and (BB3), to align riving knife to the blade. No adjustment is needed for (BB1).

3. Tighten screws (AA).

The plane of the riving knife appears to be twisted in comparison to the plane of the blade. (Can be seen looking straight

down on the blade and riving knife.)

If the riving knife has horizontal misalignment, adjust as follows using Figure 59 and Figure 61.

1. Loosen the two hex socket head screws (AA)

2. Adjust screw (BB2) to align the riving knife to the blade, if still out of alignment then adjust (BB3) until proper

alignment is achieved. Do not adjust (BB1).

3. Tighten screws (AA).

FIGURE 61

FIGURE 62

Horizontal Alignment

Vertical Alignment

MAINTENANCE

TROUBLESHOOTING

ACCESSORIES

To reduce the risk of injury, turn unit off and disconnect it from power source before cleaning or

servicing, before installing and removing accessories, before adjusting and when making repairs. An

accidental start-up can cause injury.

Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth.

NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

If your machine fails to start, check to make sure the prongs on the cord plug are making good contact in the receptacle,

and check reset button on power switch housing. Also, check for blown fuses or open circuit breakers in your power

line.

A complete line of accessories is available from your DELTA® Supplier, DELTA® Factory Service Centers and Delta®

Authorized Service Centers. Please visit our web site at www.DeltaMachinery.com for an online catalog or for the name

or your nearest supplier.

Since accessories other than those offered by DELTA® have not been tested with this product, use of

such accessories could be hazardous. For safest operation, only DELTA® recommended accessories

should be used with this product.

For assistance with your machine, visit our website at www.DeltaMachinery.com for a list of service centers or call

DELTA® Power Equipment Corporation Customer Care at 1-800-223-7278.

Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.

Specific areas which require regular maintenance include:

RIVING KNIFE CLAMP PLATE: Keep this area free of dust and debris buildup. Blow out area regularly with compressed

air.

NOTE: If the riving knife clamp can’t move freely, have the saw serviced by authorized DELTA® Power Equipment

Corporation service center personnel.

WORM GEARS: Keep the bevel gears free of dust and debris buildup. Blow out area regularly with compressed air. Use

a lithium-based multipurpose grease as needed on these gears.

CLEAN SAWDUST BUILDUP OUT OF CABINET PERIODICALLY: NOTE: Debris can also be removed from the saw

from below the throat plate, inside the dust port.

KEEP MACHINE CLEAN

FAILURE TO START

MAINTENANCE REMINDERS

46 47

Five Year Limited New Product Warranty

DE LTA

will repair or replace, at its expense and at its option, any new DELTA

machine, machine part, or machine accessory which in

normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a DELTA

factory service center or authorized service station with proof of purchase of the product within ve years and provides DELTA

with

reasonable opportunity to verify the alleged defect by inspection. For all refurbished DELTA

product, the warranty period is 180 days.

DE LTA

will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made

or specically authorized by anyone other than an authorized DELTA

service facility or representative. Under no circumstances will

DE LTA

be liable for incidental or consequential damages resulting from defective products. Some states do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty is DELTA

’s

sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or im-

plied, whether of merchantability, tness for purpose, or otherwise, are expressly disclaimed by DELTA

. For further detail of warranty

coverage and warranty repair information, visit www.DeltaMachinery.com or call 1-800-223-7278. This warranty gives you specic legal

rights and you may have other rights which vary in certain states or provinces.

WARRANTY

To register your tool for warranty service visit our website at www.DeltaMachinery.com.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, call the local

company or see website for warranty information.

All DELTA® machines and accessories are manufactured to high quality standards and are serviced by a network of

DELTA® Authorized Service Centers. To obtain additional information regarding your DELTA® quality product or to obtain

parts, service, warranty assistance, or the location of the nearest service center, please call 1-800-223-7278.

REPLACEMENT PARTS

Use only identical replacement parts. For a parts list or to order parts, visit our website at www.DeltaMachinery.com. You

can also order parts from your Authorized Warranty Service Center or by calling Customer Support at 1-800-223-7278 to

receive personalized support from one of our highly-trained representatives.

FREE WARNING LABEL REPLACEMENT

If your warning labels become illegible or are missing, call 1-800-223-7278 for a free replacement.

PARTS,SERVICE AND WARRANTY ASSISTANCE

2651 New Cut Road

Spartanburg, SC 29303

(800) 223-7278

www.DeltaMachinery.com

Power Equipment Corporation DPEC004331 - 03-28-16

Rev Date: 06-06-16