AJA KONA, Io and T-TAP™ Software Installer
Release Notes - macOS v14.3
Requirements and Recommendations
Operating System
• This version of AJA’s unied software, driver and rmware package is compatible with macOS
10.14 (Mojave), 10.13 (High Sierra) and 10.12 (Sierra). Earlier versions of macOS may continue to
work well, but are no longer tested or officially supported. For demanding workows using 4K/
UltraHD and/or higher frames rates such as 60p, AJA recommends macOS 10.14 (Mojave), or 10.13
(High Sierra).
• For additional hardware recommendations and requirements*, please see:
https://www.aja.com/support/kona-system-conguration
• Additionally, the AJA Thunderbolt Solutions page contains details to help get you up and
running as quickly as possible, including cable specications:
https://www.aja.com/solutions/thunderbolt
*Check the Known Issues and Limitations section near the end of this document. See section “Important MacOS
High Sierra Installation Information” relating to security issues for hardware recognition on rst install under macOS
High Sierra and later.
Software
The following AJA software versions are recommended for use with this installer:
AJA Control Room v14.3, Control Panel v14.3, System Test v14.3
The following 3rd party software versions are compatible with this installer.
AJA recommends the latest released versions of 3rd party software for best
performance:
*In some cases, software vendors are no longer supporting certain older versions
of macOS, so while the AJA unied package may support those OS versions, it may
not be possible for AJA to support customers or troubleshoot issues, if problems
arise with an OS that is no longer supported by 3rd party software vendor(s).
! | AJA Software Installer - macOS v14.3 www.aja.com1
Adobe
• Premiere Pro CC 2019*, 2018, 2017
• After Effects CC 2019*, 2018, 2017
• Photoshop CC 2019*, 2018, 2017
• Prelude CC 2019*, 2018, 2017
• Audition CC 2019*, 2018, 2017
Apple
• Final Cut Pro X – 10.4.x*, 10.3.2, 10.3.1,
10.3, 10.2.3
Avid
• Media Composer - 2018.x*, 8.10, 8.9, 8.8,
8.7, 8.6, 8.5, 8.4
Telestream
• Wirecast 10.x, 9.x, 8.x, 7.x, 6.x
Other Compatible Applications**
• List of AJA Compatible Software!
**Please contact the appropriate software vendor for information on AJA driver versions
required for use in their application.
New Features in v14.3
• Introduction of SMPTE ST 2110 support for AJA KONA IP (receive and transmit) up to 2K/HD 60p
• Added 6G-SDI as a valid I/O for using AJA Io 4K Plus with Telestream Wirecast* (via MultiChannel
Cong 4K settings).
Note: Wirecast setup is done via AJA Multi-channel Config (not AJA Control Panel).
New Recommendations in v14.3
• For best results when capturing using Avid Media Composer or AJA Control Room, set Ref In to
Video In with AJA KONA, AJA Io products and Avid DNxIV, DNxIP
Fixes, Changes and Improvements in v14.3
Note: Items below are identied against the main AJA products affected. These same issues may
have also affected other AJA products that are not specically called out.
! | AJA Software Installer - macOS v14.3 www.aja.com2
• QuickTime components are now legacy and have been removed from the AJA unied desktop
software package and thus, are no longer installed by default. If you still wish to obtain and install
the QuickTime components, you can nd the package under the support section for your AJA
product, inside “Software Archive”.
• For AJA Control Room, there are no dependencies on the legacy QuickTime components,
since AJA has internal QuickTime libraries which remain available to the application
• For up to date 3
rd
party NLEs and other software applications using AJA hardware, there
should be no dependencies on the legacy QuickTime components. If you need more
information, please contact your software vendor.
• VANC checkbox for “tall frame” support is now legacy and has been removed from AJA Control
Panel on Mac. This was a feature that specically supported FCP 7 and AJA VTR Xchange.
• Solved problem in AJA Control Panel when using AJA KONA HDMI, where inputs are incorrectly
reporting incoming source as YUV 4:4:4 with numerous Canon cameras
• Solved problem in AJA Control Panel when using AJA KONA HDMI, where swapping sources to
different inputs can take up to 20 seconds for the signal to be detected from some Panasonic
cameras
• Solved problem in AJA Control Panel when using AJA KONA HDMI, where inputs 1 & 2 are
incorrectly reporting incoming source as DVI (RGB 8 bit) from some Panasonic cameras
• Solved problem in AJA Control Panel when using AJA KONA HDMI, where inputs 3 & 4 are
incorrectly reporting incoming source as DVI (RGB 8 bit) from KONA 4 HDMI output
• Solved problem in AJA Control Panel when using AJA KONA HDMI, where right clicking on the
inputs within Control Panel brings up the window for the input options, but fails to switch to the
desired input change
• Solved problem in AJA Control Panel when using AJA KONA HDMI, where 4K/UHD playback will
crash the application
• Resolved issue in AJA Control Panel when using AJA KONA HDMI, Io 4K Plus or Io 4K, where
HDMI sources from MacBook Pro were not locking successfully as inputs
• Resolved issue in AJA Control Panel when using AJA KONA 1, where Follow Input is not
functioning correctly when source format changes.
• Resolved issue in AJA Control Panel when using KONA IP, KONA 4, Io 4K, where Info tab reports
bitle as "bad bitle type".
• Fixed issue with Telestream Wirecast when using Io 4K Plus, Io 4K, KONA 4, KONA IP, Io IP, Avid
DNxIV and Avid Io IP, where incoming audio was always defaulting to input from SDI 1, regardless
of setting chosen.
• Fixed issue with Telestream Wirecast where with no shot selected, incoming (pass-through) audio
was present and could not be muted on outputs for Analog, Headphones, SDI monitoring and
HDMI at application launch, when using AJA KONA or Io products.
• Resolved problem when using Apple FCPX whereby frame drops would occur at the beginning of
playback, when using AJA KONA or Io products.
! | AJA Software Installer - macOS v14.3 www.aja.com3
• Resolved problem when using Apple FCPX whereby audio might be intermittently repeated at
playback stop, when using AJA Io 4K Plus, Io 4K, Io XT, KONA 4 and KONA LHi.
• Fixed issue when using Adobe Premiere Pro CC with the capture window open, whereby
application or entire host system may crash when changing incoming video format with AJA
KONA or Io products.
• Fixed issue when using Adobe Premiere Pro CC, whereby frames are dropped upon playback of HFR
material from either captured or imported sources with AJA KONA or Io products.
• Solved issue when using Avid Media Composer, whereby Snap forward then back would occur
when starting play follow a scrub, with AJA KONA or Io products and / or Avid DNxIV, Avid
DNxIP.
• Solved issue when using Avid Media Composer, whereby application would not launch if SDI inputs
are connected to AJA KONA or Io products and / or Avid DNxIV, Avid DNxIP.
• Solved issue when using Avid Media Composer, whereby a corrupt frame was present at the start of
capture with AJA Io 4K Plus, Io IP, Avid DNxIV, Avid DNxIP.
• Improved performance when using either AJA Control Room or Avid Media Composer, whereby
capture or playback was slow to start with Reference set to Video In, with AJA KONA or Io
products.
• Solved problem when using Io XT, where Analog Audio output had phase shift at high frequencies.
• Solved problem when using Io XT (UFC rmware), where applying a secondary down-converted
output was not possible.
Features, Fixes, Changes and Improvements in Prior Releases
v.14.2.1
• Introduction of nal release for Avid DNxIP (new Avid Thunderbolt 3 device) supporting SMPTE
2022-6/7.
• Expanded analog audio conguration options for Avid DNxIV, Avid DNxIP.
• With AJA Control Panel, user can now select from four modes:
• “8 in”: eight-channel input across A1-8
• “8 out”: eight-channel output across A1-8
• “4 in, 4 out”: four-channel input across A1-4, four-channel output across A5-8
• “4 out, 4 in”: four-channel output across A1-4, four-channel input across A5-8
• Problems with 3G-SDI output are rectied for KONA LHI and KONA LHe Plus.
• Lack of audio when capturing Deep Color with HDMI ports 3 and 4 in AJA Control Room, is now
resolved with KONA HDMI.
! | AJA Software Installer - macOS v14.3 www.aja.com4
v.14.2
• Introduction of AJA KONA HDMI support (new AJA PCIe card).
• Introduction of AJA KONA 1 support (new AJA PCIe card).
• Introduction of AJA Io IP support (new AJA Thunderbolt 3 device).
• “Deep Buffer” setting in AJA Control Panel, improves handling of storage interruptions during
ingest with AJA Control Room.
• User can now allocate RAM for caching to protect media being written during
ingest:
• AJA Control Room: Preferences > Capture > “Reserve buffer size for deep
capture queues”.
• Expanded analog audio conguration options for Io 4K Plus, Avid DNxIV, Io IP, Avid DNxIP.
• With AJA Control Panel, user can now select from four modes:
• “8 in”: eight-channel input across A1-8
• “8 out”: eight-channel output across A1-8
• “4 in, 4 out”: four-channel input across A1-4, four-channel output across A5-8
• “4 out, 4 in”: four-channel output across A1-4, four-channel input across A5-8
• “Disable creation of SCC/MCC les from Closed Caption data” option in Adobe Premiere Pro CC
2017 onwards, provides user with ability to prevent automatic generation of SCC/MCC Closed
Caption les when capturing a signal with the data present:
• Adobe Premiere Premiere Pro CC > Window > Capture > Settings > Edit >
Settings > “Disable creation of SCC/MCC les from Closed Caption data”.
• Note that this option is not engaged by default. This is so older projects will remain
unaffected.
• Note that enabling this feature does not prevent the recorded media from encoding the
Closed Caption data. If the data is present in the source signal, then it will be retained in the
captured media.
• Important updates have been added to the Known Issues and Limitations section near the end of
this document. See items relating to hardware recognition on rst install under macOS High Sierra
and later.
• Amended display problem with Adobe Premiere Pro CC where during capture of ProRes 422,
ProRes HQ or DNxHR HQX, the canvas appears to show dropped frames (even though the
captured le contains all frames).
• Fixed capture problem with Adobe Premiere Pro CC where setting up for ProRes 4444 captures,
resulted instead in uncompressed BGRA clip being written disk.
• Fixed capture problem with Adobe Premiere Pro CC where when selecting RGBA for capture,
instead resulted in a black clip being written to disk.
• Solved issue with Adobe Premiere Pro CC where auto-creating a sequence from an AJA clip (in a
new project for the rst time) could either take over 30 seconds, or else crash the application.
! | AJA Software Installer - macOS v14.3 www.aja.com5
• Resolved bad SD video playback in Adobe Premiere Pro CC canvas and loss of AJA Video output,
when choosing to display both elds.
• AJA Control Room now provides a conrmation dialog if the application is quit or exited during
capture.
• Amended incorrect interface reporting in AJA Control Panel whereby it appeared that input pass-
through is checked, when actually in playback, and vice versa.
• AJA Control Panel Frame Buffer and Output are now correctly set to 525i 29.97 when presented
with P2/MXF 480i 29.97 material that is agged as 23.98.
• When Open GL acceleration is not being utilized, SD material no longer shows black at the bottom
of the frame in AJA Control Room viewer during playback.
• Fixed issue whereby T-TAP output image would shift horizontally.
• Amended behavior in Adobe Premiere Pro CC capture tool, such that it is no longer possible to
attempt to capture from T-TAP (being a monitoring-only device).
• Fixed issue whereby upon quitting / exiting Telestream Wirecast, T-TAP was left in a non-standard
conguration. AJA Control Panel reported “In use by OEM application”.
• Solved problem in AJA Control Panel, where clicking on the Timecode tab could cause the
application to crash, with T-TAP.
• Corrected various HDMI display and capture problems caused when AJA device is connected to
an already powered-up HDMI monitor , and then powered on, with Io 4K, Avid DNxIV.
• Solved intermittent issue where switching modes or moving the playhead could then cause loss
of (incoming) EE audio monitoring when using audio punch-in within Avid Media Composer. Only
monitoring was affected, as the audio captured did contain the voice over content recorded, with
Io 4K, Avid DNxIV.
• Fixed problem whereby unplugging Thunderbolt 3 cable when AJA Control Panel is set to 4K
Quad Input (Square Division), could in some instances create a kernel panic, with Io 4K, Avid DNxIV.
• Amended AJA Control Panel feedback where SDI 5 was being erroneously labelled as Video and
Key, when SDI 3 and 4 were set to Video and Key, with Io 4K, Avid DNxIV.
• Corrected banding on HDMI output when AJA Control Panel Frame buffer is set to YCbCr and
HDMI color space is set to 10bit YUV, with Io 4K, Avid DNxIV.
• Rectied problem whereby HDR would turn on, but not turn off completely, with Io 4K, Avid
DNxIV.
• Remedied audible “tapping” effect during manipulation of volume knob, with Io 4K, Avid DNxIV.
• Solved problem with AJA Control Panel where when set to Quad (Square Division) SDI input, the
HDMI output suffered from a green tint, and the HDMI widget reports incorrectly that it is passing
4K/UHD instead of a down convert to 2K/HD, with Io 4K.
• Corrected problem whereby Adobe Premiere playback of 2K formats would set the AJA
Control Panel frame buffer to UHD, with Io 4K.
• Fixed display of garbage video instead of color bars upon launching AJA Control Panel, with Io 4K,
Io XT.
• Solved loss of HDMI output when using an RGB-10 (or ARGB-8 / RGB-12) framebuffer setting and
attempting to set color space to either 10-bit YCbCr / 4:2:0, with Io 4K plus, Avid DNxIV, Io 4K,
KONA 4.
! | AJA Software Installer - macOS v14.3 www.aja.com6
• Rectied AJA Control Room problem causing the wrong color space and image aberrations to
display when using SDI RGB input, with Io 4K plus, Avid DNxIV, Io 4K, KONA 4.
• Fixed wrong output from AJA Control Panel. Upon selecting 2K, HD was instead output, and when
selecting 4K, UHD was instead output, with Io 4K, Io XT, KONA LHi.
• Solved problem where buffer format selections in AJA Control Panel intermittently provided
incorrect output raster and corrupted imagery, with KONA LHi and Io Express.
• Fixed audio quality problem when using Wirecast while running the UFC rmware available for
KONA 4.
• Fixed issue when using SMPTE 2022-6/7 rmware, whereby a receiving KONA IP would not
reestablish video streams following a manual disable and then re-enable of Video Output (in AJA
Control Panel) on the transmitting KONA IP
• Solved transmit (playback) and receive (ingest) problems with 2K formats (up to p30 max) when
using SMPTE 2022 rmware and JPEG 2000 rmware, with KONA IP.
• Solved problem in AJA Control Panel where switching from 2K to SD formats could interrupt
transmit (playback) when using SMPTE 2022-6/7 rmware on KONA IP.
• Fixed intermittent black frames showing across HDMI and SDI output with Downstream Keyer
when using FrameBuffer over Video In, with either HDMI or SDI In selected as the source (and
setting Match Frame Buffer format to Source), with KONA LHi.
• Solved locking to input problem with Downstream Keyer when using FrameBuffer over Video In,
with HDMI In selected as the source, with KONA LHi.
• Fixed missing video output when using Wirecast with KONA LHe Plus.
v14.0.2
• Added improved fan speed regulation for Io 4K Plus and Avid DNxIV
• Removed gain-knob “zipper” sound on Mic Input for Avid DNxIV
v14.0.1
• Added option for HDMI Audio Ch 3/4 Swap for Io 4K Plus and Avid DNxIV
• Added option for SDI Input / Output Quad Swap for Io 4K Plus, Io 4K, KONA 4 and Avid DNxIV
• Fixed general HDMI output timing and stability (of particular benet for HDMI 1.4 monitors)
• Fixed HDMI output issues with Kona 4 on macOS
• Fixed UltraHD HDMI output in 2SI
• Fixed intermittent input detection when HDMI is input source
• Fixed lack of Quarter Res output on SDI 3
• Fixed Closed Captioning for SD output
• Fixed input pass-through widget in Control Panel to show correct activity (HDMI down convert)
• Fixed issue whereby Control Panel reports device as both Io 4K Plus and DNxIV
• Fixed Virus Check issue with AJA Multi Channel Cong
• Reinstated Python models within macOS and Windows installers
• Fixed issue whereby Control Room would display an AV sync issue during capture (but capture
OK)
! | AJA Software Installer - macOS v14.3 www.aja.com7
• Fixed issue whereby Adobe Premiere Pro would display an AV sync issue during capture and
resultant capture was out of sync
• Fixed intermittent snapback at start of playback with Avid Media Composer
• Fixed Toggle P/PSF reactivity with Avid Media Composer (now instant)
v14.0
• Added Audio Mixer to AJA Control Panel
• Fixed issue whereby wake from sleep required FCPX restart
• Fixed reliability of Timecode out with FCPX
• Fixed issue whereby an application restart was required to recognize changes in HDR settings
changed in AJA Control Panel when running FCPX
• Fixed Kernel Panic after Sleep > Wake > Launch FCPX cycle
• Fixed issue whereby “Ioclasscount for AudioStream” did not reset to zero upon Thunderbolt plug
cycle with Apple FCPX
• Fixed reverse playback of interlaced material (where elds were incorrectly swapped) within
Adobe Premiere Pro CC
• Fixed issue with cueing clips from the bin following an icon scrub, whereby a frozen frame
manifested on playback on 1st attempt within Adobe Premiere Pro CC
• Fixed jump in playback when video delay is set past zero within Adobe Premiere Pro CC
• Fixed RP188 output from source viewer in Adobe Premiere Pro CC
• Fixed playback issue for 2Kp60 projects in Avid Media Composer
• Fixed severe frame dropping & A/V sync loss when playing AMA linked P2 AVC-I within Avid Media
Composer
• Fixed issue whereby T-TAP leaves device in OEM mode on Wirecast exit
• Fixed issue whereby Control Panel crashes if launched with no device connected
• Fixed inoperable contextual menus on Mac within Control Panel
• Added VTR on/offline icon to Batch Capture bin window in Control Room
• Fixed issue whereby device offline dialog gets stuck in loop for batch captures when clicking "OK"
in Control Room
• Fixed issues whereby Timecode for current position stops updating, when video option set to “no
video” within Control Room.
• Fixed bad timecode with playback of DPX Cineon header sequences in Control Room
• Fixed 1 second lag for actual capture to begin, with DVCProHD 'on the y' captures in Control
Room
• Now possible to choose category dividers in compressor dropdown menu as compressors within
Control Room
• Fixed failure to connect to AJA device after 2nd sleep with downstream Thunderbolt device
attached
• Fixed issue whereby AJA thunderbolt device fails to be seen after sleep/wake cycle
• Fixed issue whereby ProRes 4k 4444 clips w/ alpha don't setup AJA device correctly
• Renamed the main AJA Desktop uninstaller in Program and Features
• Fixed intermittent 720p Varicam playback issues with T-TAP
• When using Square Division with KONA 4, Io 4K, Io 4K Plus and Avid DNxIV, Quad link SDI sources
are no longer viewable in UltraHD via HDMI, instead these sources will be down-converted for HD
monitoring via HDMI
! | AJA Software Installer - macOS v14.3 www.aja.com8
NOTE: This limitation does not apply to 2SI sources.
When using 2SI, Quad link SDI sources can be monitored in UltraHD via HDMI.
• It is no longer possible to decimate HFR material in order to facilitate HDMI playback on a monitor
not capable of HFR when using KONA 4, Io 4K, Io 4K Plus.
v13.0
• Fixed video freeze occurring during loop playback in Adobe Premiere Pro CC
• Fixed bad video resulting from RGBA 8 bit capture in Adobe Premiere Pro CC
• Enabled AJA plug in for Adobe After Effects to be installed, without Premiere Pro CC
• Fixed memory leak when Capture windows left open in Adobe Premiere Pro CC
• Fixed issue whereby MXF les captured in Control Room, could not be linked to with Avid Media
Composer (File>Import>Link to media)
• Fixed a duplicate clip issue in AJA Control Room(when attempting to overwrite with new le)
• Fixed AJA Control Room GUI issues (Capture / Playback interface problematic with no input
connected)
• Fixed AJA Control Room issue with missing edit In Point (shuttling engaged via frame stepping
following “go to IN”)
• Apple ProRes now recognized on imported clips in AJA Control Room
• Improved Thunderbolt™ plug and play performance
• Fixed Timecode reporting for DF RP188 captures (DF was reported as NDF)
• Fixed Horizontal line in SDI 4 of Io 4k and KONA 4
• Fixed UHD test patterns
• Fixed ETT issues (where having a DVCproHD clip loaded caused video input distortion)
• Improved compatibility with AMD graphics cards
• Fixed DVCProHD Routing issue (stuck in DVCproHD playback)
• Fixed issue with HDMI input producing bad video with AJA Io 4K
• Fixed issue where selecting analog input as reference, causes HDMI input to instead become
reference source on AJA KONA LHi
• Improved Level B handling (on input to AJA device)
• Fixed conict between AJA desktop software and Blackmagic Design software occurring when
uninstalling AJA desktop software
v12.5.1
• Fixed Genlock selection for Analog Input Video Source on KONA LHi
• Fixed issue where12-bit HDR Color Space setting was missing on Adobe Premiere 2017
• Fixed issue where QuickTime les captured with 32-bit integer audio wouldn't play audio in some
3rd party apps
• Removed 32-bit audio option from MXF to prevent incompatibility in Adobe Premiere
• Fixed VPID issues for Dual-Link connections on all KONA and Io devices
! | AJA Software Installer - macOS v14.3 www.aja.com9
• Fixed issue whereby quick use of JKL keyboard keys on Avid Media Composer could put audio into
a loop
• Fixed issue in AJA’s Control Panel whereby AJA’s Control Panel would crash following a click of the
line in test pattern drop drown
• Fixed 2K 23.98 playback issues on T-TAP
v12.5.0
• Improved DNxHR performance on capture
• Improved Thunderbolt hotplug cycles behavior
• Fixed issue where RP188 VITC shown when only RP188 LTC is present
• Fixed issue when ANC TC on SDI 2 was not previously shown in AJA’s Control Panel
• Fixed issue where State of Genlock was not saved or recalled correctly in AJA’s Control Panel
Presets with Io XT
• Fixed issue where Ref/LTC would switch to Ref when selecting the Playback pane in AJA Control
Room with Io XT
• Fixed Capture Now offset issues between video and timecode with 9 pin set as timecode source
• Fixed issue with audio system crashes when switching from one application to another or from
one plugin instance to another on macOS
• Fixed issue with applications hanging when Io4K is hot unplugged
• Fixed many improper VPID issues
• Fixed issue with 4K/UHD 2SI input not being captured properly on KONA 4 and Io 4K
• Fixed issue where Control Room captured clips are always non-drop TC
• Fixed issue with bad output after wake from sleep on macOS
• Changed all ‘425’ strings in AJA Control Panel to read ‘2-SI’ to denote 2 Sample Interleave method
of transmitting 4K and UHD
• Fixed issue with AJA output not working in Premiere Pro after changes in Adobe Playback
Preferences
• Fixed issue with capture in Premiere Pro where selection of Stereo Audio would create les with
discrete mono tracks
• Fixed issue where closing some applications caused HDMI audio output to always reset to 8
channels
• Fixed issue where old video frame ashed on AJA output when switching from timeline to
timeline, or from timeline to source monitor in Premiere Pro.
• Fixed issue with audio stutter on Wirecast output
• Fixed issue with background noise created on live stream and recorded le in Wirecast
v12.4.1
• Fixes issue which intermittently caused AJA driver not to read the AJA hardware serial number
correctly.
v12.4.0
• Fixed issue where 8-bit YUV playback was bad in Premiere Pro with when Mercury GPU is off.
! | AJA Software Installer - macOS v14.3 www.aja.com10
• Fixed issue where switching from AJA device to Adobe Desktop Audio in the Premiere Pro
Playback preferences causes erratic behavior when the AJA device is selected as the System Audio
device in macOS.
• Removed AJAUncompressedCodec.component from the AJA Driver installer on macOS.
• Fixed issue that caused video output to freeze in Premiere Pro when performing a trim function
• Changed the way the audio hardware was being used
• Fixed issue that causes Premiere Pro to freeze and/or crash during capture on macOS 10.11
• Fixed issue where AJA Control Panel does not hold onto a user preference for 1080p high frame
rate 3G Level B. After a reboot, it always reset to Dual Link 1.5G.
• Fixed issue with audio only les in the Premiere Pro source monitor playing back with a stutter
when AJA Transmit plugin is using minimum buffer mode
• Fixed issue where legacy AJA After Effects Preview Plugin (Blithook) would not release the AJA
hardware when trying to switch out of After Effects to another application
• Changed the way Adobe After Effects is supported. Two different plugins were being installed
before. The ‘Blithook’ plugin was the old legacy plugin and is no longer installed by default. It
must be deliberately chosen as an option in the installer. The Transmit plugin is installed with the
default installation options. Please see the Adobe Plugins manual for more information.
• Added NCLC color proles to QuickTime le creation in Control Room
• Added updated DNxHR codec to Control Room and Adobe Capture plugin which improved
DNxHR capture performance.
• Fixed issue where AJA System Test failed when trying to test DMA speed on T-Tap
• Fixed issue where DV and DVCProHD codecs didn’t appear in Control Room and in Premiere Pro
capture plugin when AJA hardware was in 25 or 50 fps modes.
• Fixed issue where 1080p50/59.94/60 projects in Media Composer would always switch AJA
hardware into 3G SDI Level A Mode. Dual Link and Level B were not possible. Now, the user can
choose this setting in AJA Control Panel before Launching Media Composer, and the setting will
be honored.
• Fixed issues with controlled capture failing in Control Room
• Changed DNxHD naming conventions in AJA Control Room to match the conventions in the
DNxHR
• Fixed issue where controlled capture in AJA Control Room always created a le with 16 tracks of
audio.
• Fixed issue where 10-bit HDMI Input to Io4K was being handled as 8 Bit.
• Fixed Capture in Premiere Pro using DV compression
• Fixed issue with bad test pattern output from Io 4K after host computer sleeps (rmware update)
• Fixed issue where capture of several DNxHD clips in AJA Control Room causes Control Room to
crash
• Changed macOS and Windows installers to not install the legacy AJA After Effects Preview plugin
by default. The plugin is still inside the installer, but must be selected by the user in a custom
install. This older plugin should only be used in situations where performance of Transmit is not
fast enough.
• Fixed issue in KONA 3G where RP-188 Timecode could not be read correctly from SDI Input 2
(rmware update)
• Fixed issue where controlled capture in Control Room appears that the out value changes after
the capture begins. The out point is correctly executed, but the value appears cosmetically
incorrect.
! | AJA Software Installer - macOS v14.3 www.aja.com11
• Fixed issue where frames might be skipped at start of timeline playback from Media Composer
• Fixed issue where rst frame of playback after scrub might be incorrect frame in Media Composer
• Fixed issue where looped playback in Media Composer could cause an exception error
• Fixed issue where Video and Audio millisecond offsets in Premiere Pro Playback could cause video
to skip a few frames at the beginning of timeline playback
• Fixed cosmetic issue in AJA Control Room where VTR out point appeared to change after a
controlled capture began
• Fixed issue in KONA LHe+ where AES XLR could not be selected as the Audio Input source in the
AJA Control Panel. Requires rmware update.
• Fixed issue on Io 4K where analog audio settings were not reected correctly in AJA Control Panel
• Fixed Frame accuracy during capture of 720p formats in Adobe Premiere Pro
• Improved device control in Adobe Premiere Pro with fractional frame offsets in the device control
plugin. Fractional frame offsets can be used to tweak capture and layoff offsets by less than one
frame when edits and captures are out intermittently. Please contact AJA support for more
information.
• Fixed capture of R-188 Timecode in Premiere Pro
• Fixed issue with T-Tap and Io Express not holding their correct video format settings in Premiere
Pro
• Fixed issue with RGB HDMI input not working correctly in Io 4K
• Fixed issue with AJA Control Room not inserting the rst frame of audio during an insert edit.
• Fixed issue with AJA Import plugin for Adobe Photoshop where captures would have crushed
levels
• Fixed issue with VPID on 2-Sample Interleave formats being wrong
• Fixed banding in Io 4K and Kona 4 with HDMI output of 4K and UltraHD
• Fixed issue in KONA 4 and Io4K where images get skewed if the downstream keyer is being used
• Fixed issue where switching video formats can cause the picture to lock up in the wrong place
vertically.
• Fixed Audio and Video offset settings in Premiere Pro Playback Settings
Relevant Products
The following products are covered by this update:
Io 4K Plus
Avid DNxIV
Io IP
Avid DNxIP
Io 4K
Io XT
Io Express
T-TAP
KONA 4
KONA HMDI
KONA IP
KONA 1
KONA 3G
KONA LHi
KONA LHe Plus
! | AJA Software Installer - macOS v14.3 www.aja.com12
Known Issues and Limitations
General
•
‘System Sleep’ or ‘Hibernation’ should not be used with KONA and Io devices. All sleep and power
efficiency modes should be disabled in the operating system settings.
•
KONA LHi has only one audio system and is limited to capturing or outputting one channel at a
time with audio. In applications where multiple video inputs and outputs can be used at the
same time, the SDI input will have audio and the HDMI input will not. Additionally, if both input
and output are used simultaneously and independently (as opposed to output passed through
from input) only one channel will have audio.
•
MXF OP-1A capture in both AJA Control Room and Adobe Premiere CC does not support the
following formats :720p60, 1080i30, 1080p30, 1080p60.
Important macOS High Sierra Installation Information
•
With the introduction of macOS High Sierra (v10.13), Apple now requires that third party
application developers be identied during kernel extension installations. Failure to do so will
make AJA devices fail to operate (Unsupported AJA Device).
•
Depending on your macOS version and AJA Desktop Software installation history, the following
installation outcomes are possible:
o macOS Sierra and Earlier Supported Versions
No problems exist for AJA software installation or updates with these earlier versions of macOS.
o Earlier macOS to High Sierra Update
No problems should occur if you already have the AJA Desktop Software package
installed on macOS Sierra (or earlier) and update your Mac to High Sierra. The identication of AJA
as a trusted developer is passed from the earlier macOS to the High Sierra macOS.
o macOS High Sierra First AJA Desktop Software Install
No problems should occur if your Mac is running High Sierra macOS, you install AJA Desktop
Software for the rst time, and you follow the instructions shown during installation (Figure 5).
Figure 5. MacOS High Sierra Blocked Message Prompt
! | AJA Software Installer - macOS v14.3 www.aja.com13
Do NOT click OK. Instead click Open Security Preferences (or go to System
Preferences>Security and Privacy) and then click Allow for AJA Video Systems
developer (Figure 6).
Figure 6. MacOS High Sierra System Preferences, Allow Developer
NOTE: If after successful installation, you remove AJA applications from your computer
using the AJA Uninstaller, developer identication is retained by macOS High
Sierra. Re-installation should proceed without any problems.
•
Recovery from Installation Approval Failure
o If you just clicked OK during installation and skipped the developer approval
step, the AJA Desktop Software installation will complete, but essential extension
installations will not occur and AJA devices will not be operational (Unsupported
AJA Device).
o Apple has engineered a time window, within which you can belatedly approve
a developer after a partial installation. If you go to System Preferences>Security
and Privacy, within 30 minutes of a partial installation, the developer message
and Approve button will be available for use. After 30 minutes, however, the
message and button are removed from the window. Recovery from this involves
! | AJA Software Installer - macOS v14.3 www.aja.com14
uninstalling all AJA les (some manually), reinstalling the AJA Desktop Software
package, and clicking on Allow for AJA Video Systems developer.
•
Recovery Procedure
1. Run the AJA Uninstaller, located in the AJA Utilities folder in the Mac Applications folder.
2. Access the Users Library, which is hidden. To access the library:
a. Go to the Finder.
b. In the Finder Menu Bar and click on Go.
c. Hold down the Option key. The Library folder appears as long as the Option key is held
down.
3. Go to Library>Preferences and delete all com.aja.*.* les. There may be one le or several les.
4. Remove AJA Control Panel from the Dock, if applicable.
5. Restart the Mac.
6. Install the AJA Desktop Software package.
7. During installation click on Open Security Preferences (or go to System Preferences,>Security
and Privacy).
8. Under the General tab click on the Allow button for AJA Video Systems. The button is only
available for 30 minutes.
KONA HDMI
• Currently, some SD sources do not work correctly when using channels 1 and 2. Please use
channels 3 and/or 4 for SD ingest.
• Currently, certain HDMI camera sources do not work correctly. Please contact support so AJA
can investigate.
• Currently, when capturing with audio, the audio is not audible. The audio is captured to disk,
just not available for monitoring during capture.
Wirecast
• When conguring a multi-channel card such as Io 4K or KONA 4, the inputs must be
congured rst (using AJA Multi-Channel Cong application), if you plan to use the live
program output feature. This will set the master clock for the card (either NTSC or PAL),
otherwise the card will be set to 1080i-29.97 by default and could cause the card to attempt a
mix of PAL and NTSC clocks. Be sure to congure all of your inputs and outputs in AJA Multi-
Channel Cong prior to launching Wirecast.
Adobe Plug-Ins
• Audio output from AJA devices can be compromised when sequence framerates do not match
hardware framerates.
• This can occur when working in 720p formats other than 720p-50, 59.94, 60.
! | AJA Software Installer - macOS v14.3 www.aja.com15
• To work around this limitation, go to Premiere Pro Playback preferences, and set the AJA video
device to ‘Match Control Panel’. Then set up a cross-conversion to output 1080 format. For
example, if using a 720p-23.98 project, set the AJA Control Panel to cross-convert to
1080PsF-23.98, which is a valid SDI output.
• Timecode is not stored in crash captured clips when the timecode source is RS-422. If this is
required, use embedded timecode instead of RS-422 timecode.
• Variable frame rates (VFR) with pull down added are not adjusted for timecode.
• ‘Crash Capture’ and ‘Print to Video’ will work on Varicam frame rates over HD-SDI, but ‘Insert Edit’,
‘In/Out. Capture’, and ‘Batch Capture’ will not.
• When insert editing on Panasonic decks, destructive edits may occur too early on the tape. In
order to avoid this, be sure that menu item 202 “ID SEL” is set to “OTHER”.
• Preroll shorter than 4 seconds is not recommended for use with any deck, for capture or layback.
• Premiere Pro defaults to ‘Display First Field’ in its monitor wing menus. If interlacing issues appear
on the output of AJA hardware, try changing this setting to ‘Display Both Fields’.
• When changing from a DF tape to an NDF tape on the same deck, with the Premiere Pro capture
window open, the NDF/DF status may not be picked up correctly. If this happens, the timecode
values seen in the Premiere Pro capture window may be incorrect.
• This Issue will NOT affect users unless they are changing between DF and NDF tapes on the same
deck, in the same Premiere Pro Capture session.
• To Avoid This: Always give the new tape a new name in the ‘ Tape Name’ dialog that appears
when changing tapes and be sure to let the new tape spool up all the way before clicking
the ‘OK’ button on the dialog.
• To Fix This: Close the Premiere Pro capture window and reopen it.
• When capturing from or exporting to a Panasonic D5 deck, the timecode source setting in the AJA
Premiere Pro Device Control plug-in must be LTC+VITC.
Avid Open I/O Plug-ins
• For the AJA device to be selectable for audio-only capture in the Capture Tool, it must rst be
selected in the Capture Tool:
• Open the Capture Tool
• Select both the Video Input and Audio Input as AJA KONA or AJA Io
• Initiate your audio only capture
• For the AJA device to be selectable in the Audio Punch-In Tool, it must rst be selected in the
Capture Tool:
• Open the Capture Tool
• Select the Video Input as AJA KONA or AJA Io
• Close the Capture Tool
• Open the Audio Punch-In Tool
• Select the Input Device as AJA KONA or AJA Io
• Indenite looping of the timeline with Open I/O plug-in installed may cause Avid applications to
stop playback and give an error message.
! | AJA Software Installer - macOS v14.3 www.aja.com16
• When capturing Dual-Link RGB sources using KONA 3 or KONA 3G, the E/E pass through signal
may be incorrect on the Dual SDI output.
• The AJA hardware genlock may switch between ‘Input’ and ‘Reference’ when ‘Reference’ has been
selected in the AJA Control Panel. Specically, this is known to happen when attempting to batch
capture in Media Composer, causing some clips in the batch to not be captured. To work around
this issue, select ‘Input’ genlock in the AJA Control Panel when batch capturing.
• Occasionally analog video input will not be detected correctly in the Media Composer Capture
Tool. As a workaround, play the source video when you start up Media Composer.
AJA TV
• With the deprecation of support for legacy QuickTime components, AJA TV may no longer work
correctly.
Technical Support
AJA Technical Support is free and available to help you answer questions or resolve
issues with any of your AJA products.
To contact AJA Technical Support:
Shipping:
AJA Video Systems
180 Litton Drive,
Grass Valley.
CA 95945
USA
! | AJA Software Installer - macOS v14.3 www.aja.com17
