Instruction Manual

Printed in China 2019.11

All specifications and figures are subject to change without notice.

7504-1239-02

This content is subject to change.

Latest version can be downloaded

from www.skyrc.com

If you have any question about this document, please contact

SkyRC by sending a message to [email protected]

Instruction Manual

[Version 1.00]

Table of Contents

WARNING:

Introduction

Special Features

Warning and Safety Notes

Program Flow Chart

Explanation of Buttons

Power and Battery Connection

Charge Operation

Lithium Battery Program (LiPo/LiFe/Lilon/LiHV)

NiMH/NiCd Battery Program

Pb Lead-acid Battery Program

DJI Battery Program

DC/DC Converter

Battery Memory Set and Call Out

System Setting

Battery Voltage Meter

Battery Resistance Meter

Warning and Error Message

The Set Contains

Specification

Conformity Declaration

Regulatory Information

Commonly Used Terms

Warranty and Service

01

03

05

08

10

11

13

14

17

22

26

28

29

31

33

34

35

36

37

38

39

40

41

Congratulations on your choice of SKYRC B6 V2 DC Balance

Charger/Discharger. This unit is simple to use, but the operation

of a sophisticated automatic charger such as SKYRC B6 does

require some knowledge on the part of the user. These operating

instructions are designed to ensure that you quickly become

familiar with its functions. It is therefore important that you read

right through the Operating Instructions, Warning and Safety

Notes before you attempt to use your new charger for the first

time. We hope you have many years of pleasure and success

with your new battery charger.

SkyRC B6 V2 is a high-performance, micro processor control

charge/discharge with battery management suitable for use with

all current battery types(LiPo/LiFe/Li-Ion/LiHV/NiMH/NiCd/Pb)

batteries.The charger deliver dedicated 60W integrated power

and can fill battery at up to 6A. Except SkyRC normal charging

programs, it is versatile with the addition of AGM and Cold modes

for Lead Acid(Pb) battery.

This charger can be powered by 11-18V DC, it is able to power

DC equipment such as LED pit light, motor checker, etc.

Please BE SURE to read these INSTRUCTIONS, WARNING and

SAFETY NOTES before you use the charger for the first time.It

can be dangerous to mis-handle batteries and battery chargers,

as there is always a risk of batteries catching fire and exploding.

Mishandling batteries and battery

chargers is extremely dangerous,

which may cause fire and explosion.

Introduction

01 ·B6 V2

Never leave the charger unattended

when charging the battery.

LiPo batteries pose a severe risk of

fire if not properly handled.

Introduction

Please read this entire operating manual completely and

attentively before using this product, as it covers a wide range of

information on operating and safety. Or please do use this

product in company with a specialist!

LCD Display

DC Input

11-18V

Scroll Through

the Main Menu

Stop Any Charge

Processes

Alter Values

See the Status

of Individual Cells

Resume or Start

Charge Processes

Temperature

Sensor Port

Output Socket

Balance Lead Socket

Voltage Calibration (for expert user only)

SkyRC B6 V2 allows you to calibrate the voltage directly on the

device with a 6S LiPo battery. (For more information please contact

us at [email protected])

Battery Memory (Data Store/Load)

The charger can store up to 10 different charge/discharge profiles for

each channel. You can keep the data pertaining to program setting of

the battery of continuous charging or discharging. Users can call out

these data at any time without any special program setting.

Terminal Voltage Control(TVC)

The charger allows user to change the end voltage. (for expert user only)

Balancing Individual Cells Battery During Discharging

During the process of discharging, SKYRC B6 V2 can monitor and

balance each cell of the battery individually. Error message will be

indicated and the process will be ended automatically if the voltage of

any single one cell is abnormal.

Memory of Last Operation

SkyRC B6 V2 will memorize your last operation of charging/

discharging before power off.

AGM Charge and Cold Charge

For Pb batteries, there are two more charging modes: AGM charge

and Cold charge.

Optimized Operating Software

SkyRC B6 V2 features the so-called AUTO function that sets the

feeding current during the process of charging/discharging. For

Lithium batteries, it can help prevent overcharging which may lead to

explosion. It will disconnect the circuit automatically and alarm once

detecting malfunction, to achieve maximum safety and minimize the

trouble. All the settings can be configured by users.

Special Features

· 02 B6 V2 03 ·B6 V2

DJI Battery Program

SkyRC B6 V2 can charge batteries for DJI Mavic/Inspire with the

maximum charge current of 4A.

DC/DC Converter

SkyRC B6 V2 charger is integrated with DC power input, pumping max

power of 60W with the voltage ranging of 5-26V and 1-6A current.

These warnings and safety notes are particularly important.

Please follow the instructions for maximum safety;

otherwise the charger and the battery can be damaged or at

worst it can cause a fire.

Never leave the charger unattended when it is connected to its

power supply. If any malfunction is found, TERMINATE THE

PROCESS AT ONCE and refer to the operation manual.

Keep the charger well away from dust, damp, rain, heat, direct

sunshine and vibration. Never drop it.

The allowable DC input 11-18V.

This charger and the battery should be put on a heat-resistant,

noninflammable and nonconductive surface. Never place them on

a car seat, carpet or similar. Keep all the inflammable volatile

materials away from operating area.

Make sure you know the specifications of the battery to be

charged or discharged to ensure it meets the requirements of this

charger. If the program is set up incorrectly, the battery and

charger may be damaged .It can cause fire or explosion due to

overcharging.

Be very careful to choose the correct voltage for different types of

battery otherwise you may cause damage to the batteries. Incorrect

settings could cause the cells to fire or explode.

Standard Battery Parameters

3.7V/cell

Nominal

Voltage

Min. Discharge

Voltage

Max Charge

Voltage

Storage

Voltage

Allowable

Fast Charge

3.7V/cell

4.2V/cell

3.8V/cell

≦1C

LiPo

LiIon

3.6V/cell

4.1V/cell

≦1C

3.3V/cell

3.6V/cell

3.3V/cell

≦4C

LiFe

3.0-3.3V/cell 2.9-3.2V/cell

2.6-2.9V/cell

1.2V/cell

1.5V/cell

n/a

1C-2C

NiCd

1.2V/cell

1.5V/cell

n/a

1C-2C

NiMH

2.0V/cell

2.46V/cell

n/a

≦0.4C

Pb

0.1-1.1V/cell 0.1-1.1V/cell

1.8V/cell

LiHV

3.7V/cell

4.35V/cell

3.85V/cell

≦1C

3.1-3.4V/cell

Special Features

Re-Peak Mode of NiMH/NiCd Battery

In re-peak charge mode, the charger can peak charge the battery

once, twice or three times in a row automatically. This is good for

making the battery fully charged.

Cyclic Charging/Discharging

1 to 5 cyclic and continuous process of charge > discharge or

discharge > charge is operable for battery refreshing and balancing

to stimulate the battery's activity.

Battery Voltage Meter

The user can check battery's total voltage, the highest voltage, the

lowest voltage and each cell's voltage.

Capacity Limit

The charging capacity is always calculated as the charging current

multiplied by time. If the charging capacity exceeds the limit, the

process will be terminated automatically when you set the maximum

value.

Temperature Threshold*

The battery's internal chemical reaction will cause the temperature of

the battery to rise. If the temperature limit is reached, the process will

be terminated.

* This function is only available by connecting optional temperature

probe, which is not included in the package.

Processing Time Limit

You can also limit the maximum process time to avoid any possible

defect.

Battery Internal Resistance Meter

The user can check battery voltage and battery internal resistance.

Warning and Safety Notes

· 04 B6 V2 05 ·B6 V2

Storage Mode of Lithium Battery

“STORAGE” has the capacity to control the final battery voltage,

which is necessary and helpful for a rarely used battery.

Discharging

The main purpose of discharging is to clean residual capacity of

the battery, or to reduce the battery voltage to a defined level. The

same attention should be paid to the discharging process as

charging. The final discharge voltage should be set up correctly to

avoid deep-discharging. Lithium battery can not be discharged to

lower than the minimum voltage, or it will cause a rapid loss of

capacity or a total failure. Generally, lithium battery doesn't need

to be discharged. Please pay attention to the minimum voltage of

lithium battery to protect the battery.

Some rechargeable batteries have a memory effect. If they are

partly used and recharged before the whole charge is

accomplished, they remember this and will only use that part of

their capacity next time. This is a memory effect . It is said that

NiCd and NiMH batteries are suffering from memory effect. NiCd

has more memory effect than NiMH.

A battery pack which consists of different types of cells (including

different manufacturers)

A battery that is already fully charged or just slightly discharged.

Non-rechargeable batteries (Explosion hazard).

Batteries that require a different charge technique from NiCd,

NiMh, LiPo or Gel cell (Pb, Lead acid).

A faulty or damaged battery.

A battery fitted with an integral charge circuit or a protection circuit.

Batteries installed in a device or which are electrically linked to

other components.

Batteries that are not expressly stated by the manufacturer to be

suitable for the currents the charger delivers during the charge

process.

Please bear in mind the following points before

commencing charging:

Did you select the appropriate program suitable for the type of

battery you are charging?

Did you set up adequate current for charging or discharging?

Have you checked the battery voltage? Lithium battery packs can

be wired in parallel and in series, i.e. a 2 cell pack can be 3.7V (in

parallel) or 7.4V (in series).

Have you checked that all connections are firm and secure?

Make sure there are no intermittent contacts at any point in the

circuit.

Charging

During charge process, a specific quantity of electrical energy is

fed into the battery. The charge quantity is calculated by multiplying

charge current by charge time. The maximum permissible charge

current varies depending on the battery type or its performance,

and can be found in the information by the battery manufacturer.

Only batteries that are expressly stated to be capable of quick-

charge are allowed to be charged at rates higher than the standard

charge current.

Connect the battery to the terminal of the charger: red is positive

and black is negative. Due to the difference between resistance of

cable and connector, the charger can not detect resistance of the

battery pack, the essential requirement for the charger to work

properly is that the charge lead should be of adequate conductor

cross-section, and high quality connectors which are normally gold-

plated should be fitted to both ends.

Always refer to the manual by battery manufacturer about charging

methods, recommended charging current and charging time.

Especially, the lithium battery should be charged according the

charging instruction provided by the manufacturer strictly.

Attention should be paid to the connection of lithium battery

especially.

Do not attempt to disassemble the battery pack arbitrarily.

Please get highlighted that lithium battery packs can be wired in

parallel and in series. In the parallel connection, the battery s

capacity is calculated by multiplying single battery capacity by the

number of cells with total voltage stay the same. The voltage s

imbalance may cause fire or explosion .Lithium battery is

recommended to charge in series.

Never attempt to charge or discharge the following types

of batteries.

Warning and Safety Notes Warning and Safety Notes

· 06 B6 V2 07 ·B6 V2

Program Flow Chart Program Flow Chart

Pb NORMAL CHG

2.0A 4.0V (2P)

BATT/PROGRAM

BATT MEMORY

ENTER

[ BATT MEMORY 1 ]

ENTER SET->

ENTER

BATT TYPE

LiPo

BATT VOLTAGE

7.4V ( 2S )

CHARGE CURRENT

2.0A

DISCHG CURRENT

1.0A

DISCHG VOLTAGE

3.2V/CELL

TVC=YOUR RISK

4.20V

ENTER

BATT/PROGRAM

SYSTEM SETTING->

Rest Time

CHG>DCHG 10Min

ENTER

Safety Timer

ON 120Min

Capacity Cut-Off

ON 5000mAH

Temperature Unit

Celsius

Key Beep ON

Buzzer ON

Stop

BATT PROG

SAVE PROGRAM

ENTER

SAVE PROGRAM

SAVE….

[ BATT MEMORY 1 ]

LiPo 7.4V (2S )

[ BATT MEMORY 1 ]

C:2.0A D:1.0A

BATT TYPE

NiMH

BATT VOLTAGE

2.4V (2S)

ENTER

CHARGE CURRENT

2.0A

TRICKLE

100mA

PEAK DELAY

1Min

DISCHG CURRENT

1.0A

DISCHG VOLTAGE

0.5V/CELL

SAVE PROGRAM

ENTER

BATT TYPE

Pb

BATT VOLTAGE

4.0V (2P)

CHARGE CURRENT

2.0A

DISCHG CURRENT

1.0A

DISCHG VOLTAGE

1.8V/CELL

SAVE PROGRAM

ENTER

BATT/PROGRAM

Pb BATT

Pb DISCHARGE

1.0A 4.0V (2P)

BATT/PROGRAM

NiCd BATT

NiCd CHARGE

CURRENT 2.0A

ENTER

BATT/PROGRAM

NiMH BATT

ENTER

NiMH CHARGE

CURRENT 2.0A

BATT/PROGRAM

LiPo BATT

LiPo BALANCE CHG

2.0A 7.4V (2S)

LiPo CHARGE

2.0A 7.4V (2S)

ENTER

BATT/PROGRAM

LiFe BATT

Lilo BALANCE CHG

2.0A 7.2V (2S)

Lilo CHARGE

2.0A 7.2V (2S)

ENTER

BATT/PROGRAM

LiIo BATT

LiFe BALANCE CHG

2.0A 6.6V (2S)

LiFe CHARGE

2.0A 6.6V (2S)

ENTER

Temp Cut-Off

ON 50°C 122°F

Version

HW:1.00 SW: 1.04

Load Factory Set

Enter

ENTER

ENTER>3Seconds

NiMH Sensitivity

D.Peak  4mV

NiCd Sensitivity

D.Peak  4mV

DC Input Low

Cut-Off 11.0V

SAVE PROGRAM

SAVE….

ENTER

[ BATT MEMORY 2 ]

NiMH 2.4V (2S )

[ BATT MEMORY 2 ]

C:2.0A D:1.0A

ENTER>3Seconds

[ BATT MEMORY 2 ]

ENTER SET->

[ BATT MEMORY 3 ]

ENTER SET->

SAVE PROGRAM

SAVE….

ENTER

[ BATT MEMORY 3 ]

Pb 4.0V (2S )

[ BATT MEMORY 3 ]

C:2.0A D:1.0A

Pb DISCHARGE

1.0A 4.0V(2P)

BATT/PROGRAM

LiHV BATT

LiHV BALANCE CHG

2.0A 7.6V (2S)

LiHV CHARGE

2.0A 7.6V (2S)

ENTER

LiPo STORAGE

2.0A 7.4V (2S)

LiPo DISCHARGE

1.0A 7.4V (2S)

Lilo STORAGE

2.0A 7.2V (2S)

Lilo DISCHARGE

1.0A 7.2V (2S)

LiFe STORAGE

2.0A 6.6V (2S)

LiFe DISCHARGE

1.0A 6.6V (2S)

LiHV STORAGE

2.0A 7.6V (2S)

LiHV DISCHARGE

1.0A 7.6V (2S)

NiCd DISCHARGE

1.0A CUT: 3.2V

NiCd CYCLE

CHG>DCHG  1

NiMH DISCHARGE

1.0A CUT: 3.2V

NiMH CYCLE

CHG>DCHG 1

NiMH RE-PEAK

1

NiCd RE-PEAK

1

ENTER

Pb NORMAL CHG

2.0A 4.0V (2P)

Pb AGM CHG

2.0A 4.0V (2P)

Pb COLD CHG

2.0A 4.0V (2P)

Pb AGM CHG

2.0A 4.0V (2P)

DEC

INC

Pb COLD CHG

2.0A 4.0V (2P)

ENTER

BATT/PROGRAM

TOOL KITS

BATTERY VOLTAGE

METER

DJI DRONE BATT

TB4X

DJI DRONE BATT

Mavic

BATTERY INTERNAL

RESISTANCE

ENTER

5 3 3 mΩ

5 0 0 mΩ

TATAL: 16mΩ

ENTER

4.20 4.19 4.19 V

4.19 0.00 0.00 V

MAIN 16.78V

H4.200V L4.195V

DC/DC CONVERTER

U=0.0V I=0.0A

ENTER

Mavic CHARGE

BEFORE CHARGING

Mavic CHARGE

TURN ON BATTERY

ENTER

TB4X CHARGE

BEFORE CHARGING

TB4X CHARGE

TURN ON BATTERY

TB4X STORAGE

BEFORE CHARGING

Mavic STORAGE

BEFORE CHARGING

Mavic CHARGE

TURN ON BATTERY

TB4X CHARGE

TURN ON BATTERY

ENTER>3Seconds

LiPo BALANCE CHG

2.0A 7.4V(2S)

LiPo CHARGE

2.0A 7.4V(2S)

LiPo STORAGE

2.0A 7.4V(2S)

LiPo DISCHARGE

1.0A 7.4V(2S)

NiMH DISCHARGE

1.0A CUT: 1.0V

NiMH RE-PEAK

1

NiMH CYCLE

CHG>DCHG 1

NiMH CHARGE

CURRENT 2.0A

DEC

INC

· 08 B6 V2 09 ·B6 V2

When you are willing to alter the parameter value in the program,

press the START/ENTER button to make it blink then change the

value by pressing DEC and INC button. The value will be stored by

re-pressing the START/ENTER button. If there is another parameter

can be altered in the same screen, when you confirm the first

parameter value, the next parameter value will start to blink which

means it is ready to alert.

When you are willing to start the progress, press and hold the

START/ENTER button for 3 seconds. When you are willing to stop the

progress or go back to previous step/screen, press the BATT

PROG/STOP button once.

When you power on the charger, it will enter LiPo Battery balance

program directly. You could change the mode (balance mode, normal

charge mode, fast charge mode, store mode or discharge mode),

enter the desired charging/discharging mode, set the referred

parameter and start the progress.

If you have no request for LiPo Battery program, please press the

BATT PROG/STOP button to enter BATT PROGRAM screen.

BATT PROG / STOP Button:

It is used to stop the progress or go back to previous step/screen

DEC Button:

It is used to go through the menus and decrease the parameter value

INC Button:

It is used to go through the menus and increase the parameter value

ENTER / START Button:

It is used to enter parameter or store parameter on screen.

Explanation of Buttons Power and Battery Connection

1. Connecting to power source

12V DC Battery / Power Adapter Output DC 11-18V

STOP STATUS START

XT60

STOP STATUS START

· 10 B6 V2 11 ·B6 V2

11-18V

Adapter

4S LiPo Battery Pack

or 12V Pb Battery

NiMH

NiCd

Pb

Batt

Type

Operation

Program

Description

RE-PEAK

In re-peak charge mode, the charger can peak charge

the battery once, twice or three times in a row

automatically. This is good for confirming the battery is

fully charged, and for checking how well the battery

receives fast charges.

CYCLE

1 to 5 cyclic and continuous process of charge>discharge

or discharge>charge is operable for battery refreshing

and balancing to stimulate the battery's activity.

LiPo

LiHV

Lilon

LiFe

This charging mode is for charging LiPo/LiHV/LiFe/LiIon

battery in normal mode.

CHARGE

This program is for charging or discharging lithium battery

which will not be used for long time.

STORAGE

This mode is for balancing the voltage of lithium-polymer

battery cells while charging.

BAL

CHARGE

The charger will charge NiMH and NiCd batteries using

the charge current set by the user.

CHARGE

COLD CHG

DISCHARGE

Charging Program

Depends on different battery type, the operation programs are different.

DISCHARGE

This mode is for discharging LiPo/LiHV/LiFe/LiIon battery.

DISCHARGE

This mode is for discharging NiMH/NiCd battery.

This mode is for charging Pb battery in cold days when the

temperature is 5℃ to -20℃.

This mode is for discharging Pb battery.

NORMAL CHG

This mode is for charging Pb battery.

AGM CHG

This mode is for charging AGM battery.

1) LiPo Battery Connection

2) NiMH/NiCd or Pb Battery Connection

STOP STATUS START

TO AVOID SHORT CIRCUITS, ALWAYS CONNECT

THE CHARGE LEADS TO THE CHARGER FIRST,

AND THEN TO THE BATTERY. REVERSE THE

SEQUENCE WHEN DISCONNECTING THE PACK.

WARNING!

2. Connecting the battery

The balance wire of the battery must be connected to the charger.

Always remember to keep right polarity in the connection. Please

refer to the wiring diagram above,which shows a correct way for

your LiPo battery connection in the balance charge mode.

In the other modes, there is no request to connect the balance wire

to the balance socket in the charger.

But we suggest to charge your battery in balance mode for better

performance.

STOP STATUS START

Power and Battery Connection

This charging mode is for charging Mavic/TB4X battery

in normal mode.

CHARGE

This program is for charging or discharging Mavic/TB4X

battery which will not be used for long time.

STORAGE

Mavic

TB4X

Charge Operation

Lithium Battery Pack

NiMH Battery Pack

· 12 B6 V2 13 ·B6 V2

50%

10.20V

00301mAhC 2.0A

R shows the number of cells detected by the

charger and S is the number of cells set by

you on the previous screen. If the two

numbers are identical, press START/ENTER

to start the charging process.

Charging Status Monitor

During charge process, real-time status will be

shown as seen on the left. Print INC or DEC,

more status will show on the screen.

Program Stop

During the charging

process, press STOP

to stop the charging

process.

Program Complete

The charger is detecting the battery cell.

R shows the number of cells detected by the

charger and S is the number of cells set by

you on the previous screen. If the two numbers

are not identical, press STOP to go back to

the previous screen to recheck the number of

cells of the battery pack that you set before

going ahead.

Once the battery is fully charged, the screen

will read “FULL” and the charger will emit a

ringing sound. The charger also displays

battery voltage, charged capacity and elapsed

time.

R:3SER S:3SER

CONFIRM(ENTER)

START/ENTER

BATTERY CHECK

...............

R:3SER S:3SER

CANCEL(STOP)

Please scan and watch the tutorial video about

how to charge LiPo battery in balance mode.

Video

Tutorial

A memory profile is available for setting and storing pertinent

information for up to 10 different program sets. Once a battery

program is stored into memory, it will be retained until changed

again manually. Recalling a program memory number makes the

charger instantly ready to go!

If you do not wish to use the battery program memories, this

charger can be manually set before each use.

(1)

(2)

The following flowchart shows how the program is set manually:

BATT/PROGRAM Select

Mode Select

Program Start

Press INC and DEC to go through all the

programs and press START/ENTER to enter

LiPo BATT Program.

Battery Setting

Press INC and DEC to go through all the

modes and press START/ENTER to enter

LiPo Balance Charge Mode.

Press START/ENTER, the present value will

start to blink. Press INC and DEC to change

the value and press START/ENTER to

confirm your setting.

At the same time, the battery pack’s cell

count will start to blink, press INC and DEC

to change the value and press START/

ENTER to confirm your setting.

Press and hold START/ENTER for 3

seconds to start the program.

BATT/PROGRAM

LiPo BATT

LiPo BALANCE CHG

2.0A 11.1V (3S)

LiPo BALANCE CHG

2.0A 11.1V (3S)

LiPo BALANCE CHG

2.0A 11.1V (3S)

LiPo BALANCE CHG

2.0A 11.1V (3S)

START/ENTER

> 3 Seconds

Lithium Battery Program (LiPo/LiFe/Lilon/LiHV) Lithium Battery Program (LiPo/LiFe/Lilon/LiHV)

FULL

12.61V

00568mAh0.0A

FULL

12.61V

00:05:250.0A

· 14 B6 V2 15 ·B6 V2

Press the ENTER button and the amp rate

value will begin blinking. Use the DEC or INC

button to adjust the value to the desired rate.

Follow the instructions provided on your battery

when setting the charge current.

Press and hold the ENTER button for 3

seconds to start charging.

Once charging has commenced, the charger

will display the following real-time information:

battery type, charging current, battery voltage,

working mode, elapsed time and charged

capacity. Once the battery is fully charged, the

screen will read "FULL" and the charger will

emit a ringing sound. You can press the STOP

button at any time during the charging process

to stop charging.

NiMH/NiCd:

This program is only suitable for charging/discharging NiMH/NiCd

batteries. The B6 V2 offers the following NiMH/NiCd charge modes:

Charge, Discharge, Re-Peak and Cycle.

Selecting the Battery Type:

After powering on the B6 V2, press the INC or DEC button repeatedly

until you reach the appropriate program for the battery type you wish

to charge. For this example we have chosen the “NiMH BATT“ or

“NiCd BATT” program. Now press the ENTER button to enter the

desired program.

NiMH/NiCd Charge Mode:

BEFORE YOU BEGIN CHARGING YOUR BATTERY, MAKE SURE

YOU HAVE READ AND UNDERSTOOD ALL OF THE WARNINGS

AND SAFETY INFORMATION CONTAINED ON PAGES 05-07.

After selecting the correct battery type, if the screen does not read

“CHARGE”, use the DEC or INC buttons to change it to the

“CHARGE” mode.

BEFORE YOU BEGIN CHARGING YOUR BATTERY,

MAKE SURE YOU ARE CHARGING NIMH/NICD

BATTERIES. CHARGING LIPO BATTERY UNDER NIMH/

NICD BATTERY PROGRAM WILL CAUSE FIRE.

WARNING!

NiMH CHARGE

CURRENT 2.0A

NiMH 2.0A 6.22V

CHG 00:02:22

START/ENTER

VARIOUS INFORMATION DURING THE PROCESS

Press INC or DEC during the charging or discharging process to

view further pertinent information on the LCD screen.

Final voltage when the program ends.

Input voltage.

Safety timer ON and duration of time in

minutes.

Capacity cut-off ON and value of the set

capacity limit.

Voltage of each cell in the battery pack

when the battery is connected with

balance lead.

Internal temperature.

Temperature probe needs to be connected

to show external temperature.

Real-time status: battery type, battery

cell count, charge current, battery pack

total voltage,working mode, elapsed

time and charged capacity.

Cut-off temperature.

3.87 3.89 3.86 V

INC

Ext. Temp ----

Int. Temp 37°C

DEC

Temp Cut-Off

　　　 50C/122F

DEC

End Voltage

12.6V(3S)

IN Power Voltage

12.56V

Safety Timer

ON 120min

Capacity Cut-Off

ON 5000mAh

Lithium Battery Program (LiPo/LiFe/Lilon/LiHV)

NiMH/NiCd Battery Program

50%

10.20V

00301mAhC 2.0A

50%

10.20V

00301mAhC 2.0A

NiMH 2.0A 6.22V

CHG 00106mAh

· 16 B6 V2 17 ·B6 V2

NiMH DISCHARGE

1.3A CUT: 5.10V

NiMH/NiCd Battery ProgramNiMH/NiCd Battery Program

NiMH/NiCd Discharge Mode:

After selecting the correct battery type, use

the INC or DEC button to select the

“DISCHARGE” mode. Press the START

button and the amp rate value will begin

flashing. Use the INC or DEC buttons to

adjust the value to the desired discharge rate.

Press the START button again and the

voltage cut-off will begin to flash. Use the INC

or DEC button to adjust the value to the

desired rate.

Follow the instructions provided on your

battery when setting the voltage cut-off. The

T200 will stop discharging when the battery

has reached the preset voltage cut-off.

Press and hold the START button for 3

se con ds t o s tar t di sch ar gin g. O nc e

discharging has commenced, the charger will

display the following real-time information:

battery type, discharging current, battery

voltage, working mode, elapsed time and

discharged capacity.

When discharging is complete, the screen will

read “DONE” and the charger will emit a

ringing sound.

The charger will display the elapsed time, end

voltage and the discharged capacity in mAh.

You can press the STOP button at any time

during the discharging process to stop the

discharge process.

NiMH 0.6A 5.43V

DCH 00:02:22

NiMH DONE 5.10V

DISCHG 00:03:17

NiMH/NiCd Re-Peak Mode:

Applicable to NiMH and NiCD batteries only, in re-peak mode the

charger can peak- charge the battery once, twice, or three times in a

row automatically. This process is good for confirming that the battery

is fully charged and for verifying how well the battery can accept a fast

charge. A five-minute cool-down delay occurs after each re-peak

charge.

IN RE-PEAK MODE, THE B6 V2 USES THE CHARGE AMPERAGE

AND VOLTAGE SETTINGS ENTERED IN CHARGE MODE.

After selecting the correct battery type, use

the INC or DEC button to select the “RE-

PEAK” mode. Press the START button and

the Re-peak cycle number 1 begins to flash

on the screen. Use the INC or DEC button to

scroll through the cycle count and set a

number between 1 and 3.

Press and hold the START button for 3

seconds to start the re-peak process.

Once the Re-Peak process has begun, the

charger will display the following real-time

information: battery type, charging current,

battery voltage, elapsed time and charged

capacity.

Once the Re-Peak process has completed,

the screen will read “DONE” and the charger

will emit a ringing sound. The charger will

display the charge/discharge capacity for

each cycle. Using the + and - buttons, you

can scroll through the history data of each

cycle.

NiMH RE-PEAK

2

NiMH 2.0A 6.28V

RPC 00:04:04

START/ENTER

NiMH 0.6A 5.43V

DCH 00106mAh

NiMH 2.0A 6.28V

RPC 00686mAh

· 18 B6 V2 19 ·B6 V2

NiMH/NiCd Battery ProgramNiMH/NiCd Battery Program

NiMH/NiCd Cycle Mode:

The B6 V2 makes cycling of NiMH/NiCd batteries easy. The process of

discharging and recharging (cycling) can be performed automatically

with one simple step and will improve the performance of NiMH/NiCd

batteries. We strongly recommend cycling any battery that has been

discharged and stored for a period of time. This will increase the

remaining usable battery life and also improve the battery

performance.

After selecting the correct battery type, use

the INC or DEC button to select the “CYCLE”

mode. The Cycle Mode gives you two cycling

options: “DCHG>CHG” or “CHG>DCHG“. The

“DCHG>CHG” option will first discharge the

battery and then recharge the battery.

The “CHG>DCHG” option will first charge the

battery and then discharge the battery. If this

screen does not show your desired cycling

option, press the START button once and this

setting will begin flashing. Use the INC or

DEC button to change this setting.

Pressing the START button again will cause

the cycle count to begin flashing. Use the INC

or DEC button to change this to the number of

cycles you want the B6 V2 to run. The T200

can cycle the battery a maximum of 5 times

consecutively.

Press and hold the START button for 3

seconds to start the Cycle Mode.

Once cycling has commenced, the charger will

display the following real-time information:

battery type, charging/ discharging current,

battery voltage, working mode,elapsed time

and charged/discharged capacity. You will also

Once the cycling process is complete, the screen will read “DONE”

and the charger will emit a ringing sound. The B6 V2 will display the

charged/discharged capacity for each cycle. Using the + and -

buttons, you can scroll through this data for each cycle.

NiMH CYCLE

CHG > DCHG 1

NiMH CYCLE

CHG > DCHG 5

NiMH 2.0A 6.39V

C > D 00:04:04

START/ENTER

see “D>C“ or “C>D“. This will indicate which

cycling order you have chosen.

Either “D“ or “C“ will be flashing. This flashing

indicates which part of the cycle is currently

being executed.

NiMH 2.0A 6.39V

C > D 00034mAh

Additional NiMH/NiCd Process Information:

During the NiMH/NiCd battery charging/discharging process the B6

V2 can display a variety of information. Using the INC or DEC

buttons, you can also view the following information:

NiMH Sensitivity

D.Peak 4mV/CELL

Ext. Temp ----

Int. Temp 37 C

Safety Timer

ON 200min

In Power Voltage

12.56V

Temp Cut-off

50 C/122 F

Capacity Cut-Off

ON 5000mAh

Delta peak voltage sensitivity setting

External*/ internal temperature

Safety timer setting

Input Voltage

Temperature cut-off

Capacity limit setting

· 20 B6 V2 21 ·B6 V2

Pb AGM CHG

1.5A 12.0V(6P)

Press the START button again and the

nominal battery pack voltage will begin

flashing. Use the INC or DEC button to set the

voltage and the number of cells.

Press and hold the START button for 3

seconds to start charging.

Once charging has commenced, the charger

will display the following real-time information:

battery type, charging current, battery voltage,

working mode, elapsed time and charged

capacity.

When charging is complete, the screen will

read “FULL” and the charger will emit a ringing

sound.

Pb Lead-Acid Battery Program

This program is only suitable for charging

Pb(lead-acid) batteries with nominal voltage

ranging from 2 to 20V which are significantly

different from NiMH/NiCd batteries. Pb

batteries are suggested to charge with a low

current of 0.1C and cannot be used for fast

charging. Please follow the instructions

provided by the battery manufacturer.

The B6 offers the following Pb charge modes:

Charge, AGM, COLD and Discharge.

Pb (Lead-Acid):

BATT/PROGRAM

Pb BATT

Pb Charge Mode:

After selecting the correct battery type, use the INC or DEC button to

change it to the “CHARGE“ mode.

Press the START button and the amp rate value will begin flashing.

Use the INC or DEC buttons to adjust the value to the desired charge

rate. The amp rate should be set to 1/10th of capacity. For example, if

you are charging a 20Ah battery the charge rate should be set to 2A.

Follow the instructions provided on your battery when setting the amp

rate.

Pb Lead-acid Battery Program Pb Lead-acid Battery Program

Once charging has commenced, the charger

will display the following real-time information:

battery type, charging current, battery voltage,

working mode,elapsed time and charged

capacity.

When charging is complete, the screen will

read “FULL” and the charger will emit a ringing

sound.

P-6 1.5A 13.56V

CHG 00:02:22

Press the START button again and the

nominal battery pack voltage will begin

flashing. Use the INC or DEC button to set the

voltage and the number of cells.

Press and hold the START button for 3

seconds to start charging.

Pb Normal Charge

2.0A 12.0V(6P)

Pb AGM Mode:

After selecting the correct battery type, use the INC or DEC button to

change it to the “AGM CHARGE“ mode.

Press the START button and the amp rate value will begin flashing.

Use the INC or DEC buttons to adjust the value to the desired charge

rate. The amp rate should be set to 1/10th of capacity. For example, if

you are charging a 20Ah battery the charge rate should be set to 2A.

Follow the instructions provided on your battery when setting the amp

rate.

P-6 1.5A 13.56V

CHG 00106mAh

P-6 FULL 13.62V

CHG 00106mAh

P-6 1.5A 13.56V

AGM CHG 00:02:22

P-6 1.5A 13.56V

AGM CHG 00106mAh

P-6 FULL 13.62V

AGM CHG 00106mAh

· 22 B6 V2 23 ·B6 V2

Once discharging has commenced, the

charger will display the following real-time

information: battery type, cell count,discharging

current, battery voltage, elapsed time and

discharged capacity.

When discharging is complete, the screen will

read “DONE” and the charger will emit a

ringing sound.

Additional Pb Process Information:

During the Pb battery charging/discharging process the B6 V2 can

display a variety of information. Using the INC or DEC buttons you can

also view the following information:

Capacity Cut-Off

ON 5000mAh

Temp Cut-off

50 C

In Power Voltage

12.56V

Safety Timer

ON 200min

Ext. Temp ----

Int. Temp 37 C

Capacity cut-

off setting

Temperature

cut-off

Input voltage

Safety timer

setting

External*/

internal

temperature

Pb Discharge Mode:

After selecting the correct battery type, use the INC or DEC buttons

to change it to the “DISCHARGE“ mode.

Press the START button and the amp rate value will begin flashing.

Use the INC or DEC buttons to adjust the value to the desired

discharge rate. Follow the instructions provided with your battery

when setting the amp rate.

Press the START button again and the

nominal battery pack voltage will begin

flashing. Use the INC or DEC buttons to set

the voltage and the number of cells.

Press and hold the START button and

discharging will begin.

Pb Discharge

1.5A 12.0V(6P)

Pb Cold Mode:

Pb COLD CHG

1.5A 12.0V(6P)

Pb Lead-acid Battery Program Pb Lead-acid Battery Program

Press the START button again and the

nominal battery pack voltage will begin

flashing. Use the INC or DEC button to set the

voltage and the number of cells.

Press and hold the START button for 3

seconds to start charging.

Once charging has commenced, the charger

will display the following real-time information:

battery type, charging current, battery voltage,

working mode, elapsed time and charged

capacity.

When charging is complete, the screen will

read “FULL” and the charger will emit a ringing

sound.

P-6 1.5A 13.56V

COLD CHG 00:02:22

P-6 1.5A 13.56V

COLD CHG 00106mAh

P-6 FULL 13.62V

COLD CHG 00106mAh

P-6 1.5A 13.56V

DCH 00:02:22

P-6 1.5A 13.56V

DCH 00106mAh

P-6 DONE 13.62V

DCHG 00106mAh

· 24 B6 V2 25 ·B6 V2

DJI Battery Program DJI Battery Program

Press the ENTER button and the amp rate

value will begin blinking. Use the INC or DEC

button to adjust the value to the desired rate.

Follow the instructions provided on your

battery when setting the charge current.

Press and hold the ENTER button for 3 seconds

to start charging.

Once charging has commenced, the charger

will display the following real-time information:

charging current, battery voltage, working

mode, elapsed time and charged capacity.

Once the battery is fully charged, the screen

will read "FULL" and the charger will emit a

ringing sound. You can press the STOP

button at any time during the charging

process to stop charging.

This program is only suitable for charging/ discharging DJI Mavic

and TB4X battery, B6 offers two operation modes: charge and

storage.

Selecting the Battery Type:

After powering on the B6 V2, press DEC or INC, DJI BATT program

involved in the "TOOL KITS" program, press the INC or DEC button

repeatedly until you reach the appropriate program for the battery

type you wish to charge. For this example we have chosen the "DJI

DRONE BATT Mavic" or "DJI DRONE BATT TB4X" program. Now

press the ENTER button to enter the desired program.

Connect the battery to the charger as show on the diagram.

Turn on the battery before you put it in charging mode.

CONNECTION DIAGRAMCONNECTION DIAGRAMCONNECTION DIAGRAM

Note: Mavic charging cable is not included

in the package

Press the Power Button once

Then Press Again and Hold

for 2 Seconds to Turn On

BATT/PROGRAM

TOOL KITS

DJI DRONE BATT

Mavic

Charge Mode:

When the battery is idle for temporary days, it is

better to charge/ discharge the battery to 65%

of total power in order to prevent swelling.

Turn on the battery before you put it in storage

mode.

After selecting the correct battery type, use

the INC or DEC button to change the charge

mode to "STORAGE" mode setting.

Press the ENTER button and the amp rate

value will begin blinking. Use the INC or DEC

button to adjust the value to the desired rate.

Follow the instructions provided on your battery

when setting the charge current.

Press and hold the ENTER button for 3 seconds

to start charging.

Once charging has commenced, the charger

will display the following real-time information:

charging current, battery voltage, working

mode, elapsed time and charged capacity.

Once the battery is fully charged, the screen

will read "DONE" and the charger will emit a

ringing sound. You can press the STOP button

at any time during the charging process to

stop charging.

Storage Mode:

ENTER

Mavic CHARGE

TURN ON BATTERY

BATT/PROGRAM

TOOL KITS

DJI DRONE BATT

Mavic

ENTER

Mavic CHARGE

TURN ON BATTERY

Mavic STORAGE

TURN ON BATTERY

PRESSENTER>3"

+ -

50%

10.20V

00301mAhC 2.0A

FULL

12.61V

00568mAh0.0A

FULL

12.61V

00:05:250.0A

50%

10.20V

00301mAhC 2.0A

DONE

12.61V

00568mAh0.0A

DONE

12.61V

00:05:250.0A

· 26 B6 V2 27 ·B6 V2

DC / DC Converter

B6 V2 charger is integrated with a DC/DC converter. A DC/DC

converter is an electronic circuit that converts a source of direct

current (DC) from one voltage level to another. It is a type of electric

power converter. For B6 V2, the output voltage range from 5-26V

and output current range from 1-6A. The maximum power is 60W.

This program can be found in the "TOOL

KITS", press DEC or INC button repeatedly

until you reach "DC/DC CONVERTER"

program, double press the ENTER, then

press DEC or INC to set the output voltage

and current.

Press and hold the ENTER button for 3

seconds, the charger will start to work as

a power supply, you can read the output

voltage/ current / power on the screen.

Battery Memory Set and Call Out

[ B A T T M EM O R Y 1 ]

E N T E R SE T - >

B A T T T YP E

L i P o

B A T T V OL T S

7 . 4 V ( 2 S )

C H A R GE C U R R EN T

4 . 9 A

D S C H C UR R E N T

2 . 0 A

D S C H V OL T A G E

3 . 0 V /C E L L

START/ENTER

DEC INC

The charger can store up to 10 different charge/discharge profiles for

your convenience, and the stored profiles can be recalled quickly

without having to go through the setup process.

When you are willing to alter the parameter value in the program,

press START/ENTER to make it blink then change the value with INC

or DEC. The value will be stored by pressing START/ENTER once.

Note: All following screen are taking 2S(7.4V) LiPo battery for

example.

Enter the battery memory program.

(10 different charge/discharge profiles can

be stored).

Set the battery type(LiPo/LiHV/LiFe/LiIon/

NiMH/NiCd/Pb).

Set the voltage and number of cells(1-6S).

Set the charge current(0.1-6.0A).

Set the discharge current (0.1A-2.0A).

Set the discharge voltage(3.0-3.3V/Cell).

1. Battery Memory Set

BATT/PROGRAM

TOOL KITS

DC/DC CONVERTER

U=0.0V I=0.0A

ENTER

PRESSENTER>3"

Caution: The maximum DC Power output is 60 Watts. Please check

your device loading before you allocate the power.

· 28 B6 V2 29 ·B6 V2

DC/DC CONVERTER

U=6.0V I=3.4A

U=5.9V I=1.2A

POWER=7W

STOP STATUS START

DC Input

(11-18V)

DC Output

(5-26V / 1-6A)

E N T ER C H A R G ER

L O A D

L i P o BA L A N C E CH G

4 . 9 A 7. 4V ( 2 S)

S A V E PR O G R A M

S A V E .

[ B A T T ME M O R Y 1 ]

L i P o  7. 4 V ( 2 S )

[ B A T T ME M O R Y 1 ]

C : 4 .9 A D: 2 . 2A

START/ENTER

>3 Seconds

T V C = YO U R R I SK

4 . 2 0 V

DEC INC

S A V E P RO G R A M

E N T E R

START/ENTER

Set the terminal voltage(4.18-4.25V).

Press ENTER to save program.

Indicate the battery type and battery cell of the

saved profile.

Indicate the charge and discharge current of

the saved profile.

Press the START/ENTER for 3 seconds to call

out the memory.

2. Battery Memory Call Out

Load the memory set

Press START/ENTER for 3 seconds to start

the process.

Battery Memory Set and Call Out System Setting

S a f e t y T i m er

O N 1 2 0 M i n

R e s t T i m e

C H G > D C H G 1 0 Mi n

C a p a c i t y C ut - Of f

O N 5 0 0 0 m A H

T e m p e r a t ur e U ni t

C e l s i u s

T e m p C u t - O ff

O N 5 0 C 12 2 F

This program sets the maximum

charge capacity that will be

supplied to the battery during

charge. If the delta peak voltage is

not detected nor the safety timer

expired by any reason, this feature

will automatically stop the process

at the selected capacity value.

When you start a charge process,

the integral safety timer

automatically starts running at the

same time. This is programmed to

prevent overcharge the battery if it

proves to be faulty, or if the

termination circuit cannot detect

the battery full. The value for the

safety timer should be generous

enough to allow a full charge of

the battery.

The battery's internal chemical

reaction will cause the

temperature of the battery to rise.

If the temperature limit is reached,

the process will be terminated.

OFF/

ON

(100-50000mAh)

It will be operated with the default value of the essential user settings

when it is powered on for the first time.The screen displays the

following information in sequence and the user can change the value

of parameter on each screen.

When you are willing to alter the parameter value in the program,

press START/ENTER to make it blink then change the value with INC

or DEC. The value will be stored by pressing START/ENTER once.

ITEM SELECTION DESCRIPTION

OFF/

ON

(1-720 Min)

OFF/

ON

(20 C/68 F -

80 C/176 F)

Celsius

Fahrenheit

1-60Min

A rest time allowing the battery to

cool down between

charging/discharging cycle.

You can choose the temperature

displayed by Celsius or Fahrenheit

as you like.

· 30 B6 V2 31 ·B6 V2

ITEM

SELECTION DESCRIPTION

N i M HS e n s i ti v it y

D . P e a k D e f au l t

N i C dS e n s i ti v it y

D . P e a k D e f au l t

Default:

4mV/Cell

3-15mV/Cell

K e y B e e p O N

B u z z e r O N

OFF/ON

The beep sounds at every time

touching the buttons to confirm

your action. The beep or melody

sounded at various times during

operation to alert different mode

changes.

L o a d F a c t o ry S e t

E n t e r

V e r s i o n

H W : 1 . 0 0 S W : 1. 0 4

This program is for NiMH/NiCd

battery only. When the charger

detects the delta peak value

reaches the value you set, the

charger will say the battery is fully

charged.

Press ENTER to load factory

default setting.

It indicates the hardware and

firmware version.

D C I n p u t L o w

C u t - O f f  1 1 .0 V

10-12V

There will be error message when

DC input voltage is lower than the

reset value.

System Setting

Battery Voltage Meter

STOP STATUS START

The user can check battery's total voltage, the highest voltage, the

lowest voltage and each cell's voltage.

Please connect the battery to the charger main battery lead to

battery socket and balance wires to balance socket.

Press the START/ENTER to enter the Lithium

Battery Meter program.

The screen indicate each cell's voltage.

The screen indicate the total voltage, the

highest voltage and the lowest voltage.

B A T T/ P R O G RA M

B A T T ME TE R

4 . 2 0 4. 1 9 4 . 1 9 V

4 . 1 8 4. 1 8 4 . 1 9 V

M A I N 25 . 1 3 V

H 4 . 20 0 V L 4 . 18 2 V

START

ENTER

INC

This diagram shows

the correct way to

connect your battery

to check the voltage.

Lithium Battery Pack

4.20 4.19 4.19V

4.18 4.18 4.19V

· 32 B6 V2 33 ·B6 V2

Battery Resistance Meter

The user can check battery's total resistance, the highest resistance,

the lowest resistance and each cell's resistance.

Please connect the battery to the charger main battery lead to battery

socket and balance wires to balance socket.

Press the START/ENTER to enter the Lithium

Battery Resistance program.

The screen indicate each cell's resistance.

The screen indicate the total resistance, the

highest resistance and the lowest resistance.

Start

Enter

B A T T/ P R O G RA M

B A T T RE S I S T AN C E

0 1 2 0 05 0 05 mΩ

0 0 6 0 08 0 06 mΩ

T A T A L:4 2 mΩ

INC

STOP STATUS START

Lithium Battery Pack

This diagram shows

the correct way to

connect your battery to

check the resistance.

Warning and Error Message

In case of an error the screen will display the cause of error and emit

an audible sound.

Incorrect polarity connected.

The battery is interrupted.

The battery cell you sent is different from what

charger detected.

Input voltage less than 11V

Input voltage higher than 18V

The internal temperature of the unit goes too high.

The external temperature of the battery goes

too high.

The battery capacity is more than the maximum

capacity which the user sets.

The charging time is longer than the maximum

charging time which the user sets.

Battery voltage wrong.

One cell voltage of your battery is too high.

Wrong battery type.

C E L L N O T M A T C H

S U P P L Y V O L T

T O O L O W

I N T E R N A L T E MP .

T O O H I G H

S U P P L Y V O L T

T O O H I G H

B A T T T E M P E R AT U RE

T O O H I G H

O V E R C H A R G E

C A P A C I T Y L I MI T

O V E R T I M E L I M IT

V O L T E R R O R

C E L L V O L T E R R O R

W R O N G B A T T T Y P E

0 1 2 0 0 5 0 0 5 mΩ

0 0 6 0 0 8 0 0 6 mΩ

· 34 B6 V2 35 ·B6 V2

THESETCONTAINS

Specification

Balance Current: 300mA/cell

Reading Voltage Range: 0.1-26.1V/cell

Battery Types/Cells: LiPo/LiHV/LiFe/LiIon: 1-6cells

NiMH/NiCd: 1-15cells

 Pb: 2-20V

Battery Capacity Range: NiMH/NiCd: 100-50000mAh

LiPo/LiHV/LiFe/LiIon: 100-50000mAh

Pb: 100-50000mAh

Charge Current: NiMH/NiCd/LiPo/LiHV/LiFe/Li-ION/Pb: 0.1A-6.0A

DJI Mavic/TB4X: 4A

Safety Timer: 1-720minutes off

Charge Wattage: 60W

Discharge Current: 0.1A-2.0A

Discharge Cut-off Voltage: NiMH/NiCd: 0.1-1.1V/cell

LiPo: 3.0-3.3V/cell LiHV: 3.1-3.4V/Cell

LiFe: 2.6-2.9V/cell LiIon: 2.9—3.2V/cell

Pb: 1.8-2.0V/cell

Discharge Wattage: 5W

Balance Cells: 2-6 cells

Memory: 10 different charge/discharge profiles

Charge Method: CC/CV for lithium types and lead (Pb) batteries

Delta-peak Sensitivity for NiMH/NiCd.

DC Input Voltage:11-18V

Display Type: 2x16 LCD Display Backlight: Blue

Case Material: Aluminium Controls: Four Buttons

Case Size: 115x84x31mm Weight: 238g

External Port: 1-6S Balance Socket-XH, Temperature Probe Socket,

Battery Socket, DC Input.

Delta Peak Detection for NiMH/NiCd: 3-15mV/cell / Default: 4mV/cell

Battery Cutoff Temperature: 20ºC/68ºF-80ºC/176ºF(adjustable)

Charge Voltage: NiMH/NiCd: Delta peak detection

 LiPo: 4.18-4.25V/cell

LiHV:4.25-4.35V/cell

LiFe: 3.58-3.7V/cell

LiIon: 4.08-4.2V/cell

Pb Normal:2.4V/cell

Pb AGM:2.45V/cell

Pb Cold:2.45V/cell

Ec3 Charging Cable

SK-600023-13

Dean Charging Cable

SK-600023-15

Tamiya Charging Cable

SK-600023-12

4mm/5mm Bullet

Charging Cable for 2S Battery

SK-600023-14

5mm

4mm

Temperature Sensor

SK-600040-01

RECOMMENDED ACCESSORIES

The Set Contains

· 36 B6 V2 37 ·B6 V2

1. SKYRC B6 V2 Charger

2. DC Input Cable

3. Dean Charging Cable

4. Bare charging cable

5. Instruction Manual

ersion 1.00]

1

2

5

3

4

Instruction Manual

[Version 1.00]

This symbol means that you must dispose of electrical from the

General household waste when it reaches the end of its useful

life. Take your charger to your local waste collection point or

recycling centre. This applies to all countries of the European Union,

and to other European countries with a separate waste collection

system.

SkyRC B6 V2 satisfy all relevant and mandatory EC directives and FCC

Part 15 Subpart B.

FCC Part 15, Subpart B

Radiated Emission

Conformity Declaration Regulatory Information

FCC Note:

This device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that

may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modifications or change to this equipment.

Such modifications or change could void the user's authority to

operate the equipment.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF exposure guidelines, this

equipment should be installed and operated with a minimum distance

of 20cm between the radiator and your body.

· 38 B6 V2 39 ·B6 V2

EN 55014-1:2006

+ A1:2009+A2:2011

Electromagnetic compatibility-Requirements

for household appliances, electric tools and

Similar apparatus – Part 1: Emission

EN 55014-2:1997+

A1:2001+ A2:2008

Electromagnetic compatibility-Requirements

for household appliances, electric tools and

Similar apparatus – Part 2: Immunity-Product

family standard

Commonly Used Terms

Commonly used terms

Final charge voltage: the voltage at which the battery's charge limit

(capacity limit) is reached. The charge process switches from a high

current to a low maintenance rate (trickle charge) at this point. From

this point on further high current charging would cause overheating

and eventual terminal damage to the pack.

Final discharge voltage: the voltage at which the battery's discharge

limit is reached. The chemical composition of the batteries determines

the level of this voltage. Below this voltage the battery enters the deep

discharge zone. Individual cells within the pack may become reverse

polarized in this condition, and this can cause permanent damage.

A, mA: unit of measurement relating to charge or discharge

current.1000 mA = 1 A (A=Ampere,mA=Milliampere)

Ah, mAh: unit of measurement for the capacity of a battery (Amperes

x time unit; h = hour). If a pack is charged for one hour at a current of 2

A, it has been fed 2 Ah of energy. It receives the same quantity of

charge (2 Ah) if it is charged for 4 hours at 0.5 A, or 15 minutes (=1/4

h) at 8 A.

'C'-rating: Capacity is also referred to as the 'C' rating. Some battery

suppliers recommend charge and discharge currents based on the

battery 'C' rating. A battery's '1C' current is the same number as the

battery's rated capacity number, but noted in mA or amps. A 600mAh

battery has a 1C current value of 600mA, and a 3C current value of (3

x 600mA) 1800mA or 1.8A. The 1C current value for a 3200mAh

battery would be 3200mA (3.2A).

Nominal voltage(V): The nominal voltage of the battery pack can be

determined as follows;

-.NiCd or NiMH: multiply the total number of cells in the pack by 1.2. A

8-cell pack will have a nominal voltage of 9.6 volts (8x1.2).

-.LiPo: multiply the total number of cells in the pack by 3.7. A 3-cell

LiPo wired in series will have a nominal voltage of 11.1 volts (3x3.7).

-.LiIo: multiply the total number of cells in the pack by 3.6. A 2-cell LiIo

wired in series will have a nominal voltage of 7.2 volts (2x3.6).

-.LiFe: multiply the total number of cells in the pack by 3.3. A 4-cell LiIo

wired in series will have a nominal voltage of 13.2 volts (4x3.3).

If the nominal voltage of the battery is not printed on the battery's label,

consult your battery manufacturer or supplier. Do not guess the rated

voltage of battery.

Warranty and Service

This charger is designed and approved exclusively for use with the types of

battery stated in this Instruction Manual. SkyRC accepts no liability of any

kind if the charger is used for any purpose other than that stated.

We are unable to ensure that you follow the instructions supplied with the

charger, and we have no control over the methods you employ for using,

operating and maintaining the device. For this reason we are obliged to

deny all liability for loss, damage or costs which are incurred due to the

incompetent or incorrect use and operation of our products, or which are

connected with such operation in any way.Unless otherwise prescribed by

law, our obligation to pay compensation, regardless of the legal argument

employed, is limited to the invoice value of those SkyRC products which

were immediately and directly involved in the event in which the damage

occurred.

Liability exclusion

Warranty and service

We guarantee this product to be free of manufacturing and assembly defects

for a period of one year from the time of purchase. The warranty only applies

to material or operational defects, which are present at the time of purchase.

During that period, we will repair or replace free of service charge for products

deemed defective due to those causes.

This warranty is not valid for any damage or subsequent damage arising as a

result of misuse, modification or as a result of failure to observe the procedures

outlined in this manual.

The warranty service is valid in China only.

If you need warranty service overseas, please contact your dealer in the

first instance, who is responsible for processing guarantee claims

overseas. Due to high shipping cost, complicated custom clearance

procedures to send back to China. Please understand SkyRC can't

provide warranty service to overseas end user directly.

If you have any questions which are not mentioned in the manual,

please feel free to send email to [email protected]

Note:

1.

2.

3.

· 40 B6 V2 41 ·B6 V2